Struct rp_pac::dma::regs::CtrlTrig

#[repr(transparent)]
pub struct CtrlTrig(pub u32);

DMA Channel 6 Control and Status

Tuple Fields

0: u32

Implementations

impl CtrlTrig

pub const fn en(&self) -> bool

DMA Channel Enable. When 1, the channel will respond to triggering events, which will cause it to become BUSY and start transferring data. When 0, the channel will ignore triggers, stop issuing transfers, and pause the current transfer sequence (i.e. BUSY will remain high if already high)

pub fn set_en(&mut self, val: bool)

DMA Channel Enable. When 1, the channel will respond to triggering events, which will cause it to become BUSY and start transferring data. When 0, the channel will ignore triggers, stop issuing transfers, and pause the current transfer sequence (i.e. BUSY will remain high if already high)

pub const fn high_priority(&self) -> bool

HIGH_PRIORITY gives a channel preferential treatment in issue scheduling: in each scheduling round, all high priority channels are considered first, and then only a single low priority channel, before returning to the high priority channels. This only affects the order in which the DMA schedules channels. The DMA’s bus priority is not changed. If the DMA is not saturated then a low priority channel will see no loss of throughput.

pub fn set_high_priority(&mut self, val: bool)

HIGH_PRIORITY gives a channel preferential treatment in issue scheduling: in each scheduling round, all high priority channels are considered first, and then only a single low priority channel, before returning to the high priority channels. This only affects the order in which the DMA schedules channels. The DMA’s bus priority is not changed. If the DMA is not saturated then a low priority channel will see no loss of throughput.

pub const fn data_size(&self) -> DataSize

Set the size of each bus transfer (byte/halfword/word). READ_ADDR and WRITE_ADDR advance by this amount (1/2/4 bytes) with each transfer.

pub fn set_data_size(&mut self, val: DataSize)

Set the size of each bus transfer (byte/halfword/word). READ_ADDR and WRITE_ADDR advance by this amount (1/2/4 bytes) with each transfer.

pub const fn incr_read(&self) -> bool

If 1, the read address increments with each transfer. If 0, each read is directed to the same, initial address. Generally this should be disabled for peripheral-to-memory transfers.

pub fn set_incr_read(&mut self, val: bool)

If 1, the read address increments with each transfer. If 0, each read is directed to the same, initial address. Generally this should be disabled for peripheral-to-memory transfers.

pub const fn incr_write(&self) -> bool

If 1, the write address increments with each transfer. If 0, each write is directed to the same, initial address. Generally this should be disabled for memory-to-peripheral transfers.

pub fn set_incr_write(&mut self, val: bool)

If 1, the write address increments with each transfer. If 0, each write is directed to the same, initial address. Generally this should be disabled for memory-to-peripheral transfers.

pub const fn ring_size(&self) -> u8

Size of address wrap region. If 0, don’t wrap. For values n > 0, only the lower n bits of the address will change. This wraps the address on a (1 << n) byte boundary, facilitating access to naturally-aligned ring buffers. Ring sizes between 2 and 32768 bytes are possible. This can apply to either read or write addresses, based on value of RING_SEL.

pub fn set_ring_size(&mut self, val: u8)

Size of address wrap region. If 0, don’t wrap. For values n > 0, only the lower n bits of the address will change. This wraps the address on a (1 << n) byte boundary, facilitating access to naturally-aligned ring buffers. Ring sizes between 2 and 32768 bytes are possible. This can apply to either read or write addresses, based on value of RING_SEL.

pub const fn ring_sel(&self) -> bool

Select whether RING_SIZE applies to read or write addresses. If 0, read addresses are wrapped on a (1 << RING_SIZE) boundary. If 1, write addresses are wrapped.

pub fn set_ring_sel(&mut self, val: bool)

Select whether RING_SIZE applies to read or write addresses. If 0, read addresses are wrapped on a (1 << RING_SIZE) boundary. If 1, write addresses are wrapped.

pub const fn chain_to(&self) -> u8

When this channel completes, it will trigger the channel indicated by CHAIN_TO. Disable by setting CHAIN_TO = (this channel).

pub fn set_chain_to(&mut self, val: u8)

When this channel completes, it will trigger the channel indicated by CHAIN_TO. Disable by setting CHAIN_TO = (this channel).

pub const fn treq_sel(&self) -> TreqSel

Select a Transfer Request signal. The channel uses the transfer request signal to pace its data transfer rate. Sources for TREQ signals are internal (TIMERS) or external (DREQ, a Data Request from the system). 0x0 to 0x3a -> select DREQ n as TREQ

pub fn set_treq_sel(&mut self, val: TreqSel)

Select a Transfer Request signal. The channel uses the transfer request signal to pace its data transfer rate. Sources for TREQ signals are internal (TIMERS) or external (DREQ, a Data Request from the system). 0x0 to 0x3a -> select DREQ n as TREQ

pub const fn irq_quiet(&self) -> bool

In QUIET mode, the channel does not generate IRQs at the end of every transfer block. Instead, an IRQ is raised when NULL is written to a trigger register, indicating the end of a control block chain. This reduces the number of interrupts to be serviced by the CPU when transferring a DMA chain of many small control blocks.

pub fn set_irq_quiet(&mut self, val: bool)

In QUIET mode, the channel does not generate IRQs at the end of every transfer block. Instead, an IRQ is raised when NULL is written to a trigger register, indicating the end of a control block chain. This reduces the number of interrupts to be serviced by the CPU when transferring a DMA chain of many small control blocks.

pub const fn bswap(&self) -> bool

Apply byte-swap transformation to DMA data. For byte data, this has no effect. For halfword data, the two bytes of each halfword are swapped. For word data, the four bytes of each word are swapped to reverse order.

pub fn set_bswap(&mut self, val: bool)

Apply byte-swap transformation to DMA data. For byte data, this has no effect. For halfword data, the two bytes of each halfword are swapped. For word data, the four bytes of each word are swapped to reverse order.

pub const fn sniff_en(&self) -> bool

If 1, this channel’s data transfers are visible to the sniff hardware, and each transfer will advance the state of the checksum. This only applies if the sniff hardware is enabled, and has this channel selected. This allows checksum to be enabled or disabled on a per-control- block basis.

pub fn set_sniff_en(&mut self, val: bool)

If 1, this channel’s data transfers are visible to the sniff hardware, and each transfer will advance the state of the checksum. This only applies if the sniff hardware is enabled, and has this channel selected. This allows checksum to be enabled or disabled on a per-control- block basis.

pub const fn busy(&self) -> bool

This flag goes high when the channel starts a new transfer sequence, and low when the last transfer of that sequence completes. Clearing EN while BUSY is high pauses the channel, and BUSY will stay high while paused. To terminate a sequence early (and clear the BUSY flag), see CHAN_ABORT.

pub fn set_busy(&mut self, val: bool)

This flag goes high when the channel starts a new transfer sequence, and low when the last transfer of that sequence completes. Clearing EN while BUSY is high pauses the channel, and BUSY will stay high while paused. To terminate a sequence early (and clear the BUSY flag), see CHAN_ABORT.

pub const fn write_error(&self) -> bool

If 1, the channel received a write bus error. Write one to clear. WRITE_ADDR shows the approximate address where the bus error was encountered (will not be earlier, or more than 5 transfers later)

pub fn set_write_error(&mut self, val: bool)

If 1, the channel received a write bus error. Write one to clear. WRITE_ADDR shows the approximate address where the bus error was encountered (will not be earlier, or more than 5 transfers later)

pub const fn read_error(&self) -> bool

If 1, the channel received a read bus error. Write one to clear. READ_ADDR shows the approximate address where the bus error was encountered (will not be earlier, or more than 3 transfers later)

pub fn set_read_error(&mut self, val: bool)

If 1, the channel received a read bus error. Write one to clear. READ_ADDR shows the approximate address where the bus error was encountered (will not be earlier, or more than 3 transfers later)

pub const fn ahb_error(&self) -> bool

Logical OR of the READ_ERROR and WRITE_ERROR flags. The channel halts when it encounters any bus error, and always raises its channel IRQ flag.

pub fn set_ahb_error(&mut self, val: bool)

Logical OR of the READ_ERROR and WRITE_ERROR flags. The channel halts when it encounters any bus error, and always raises its channel IRQ flag.

Trait Implementations

impl Clone for CtrlTrig

fn clone(&self) -> CtrlTrig

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Default for CtrlTrig

fn default() -> CtrlTrig

Returns the “default value” for a type.

impl PartialEq<CtrlTrig> for CtrlTrig

fn eq(&self, other: &CtrlTrig) -> bool

This method tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

This method tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl Copy for CtrlTrig

impl Eq for CtrlTrig

impl StructuralEq for CtrlTrig

impl StructuralPartialEq for CtrlTrig