#[repr(transparent)]pub struct UartlcrH(pub u32);Expand description
Line Control Register, UARTLCR_H
Tuple Fields§
§0: u32Implementations§
source§impl UartlcrH
impl UartlcrH
sourcepub const fn brk(&self) -> bool
pub const fn brk(&self) -> bool
Send break. If this bit is set to 1, a low-level is continually output on the UARTTXD output, after completing transmission of the current character. For the proper execution of the break command, the software must set this bit for at least two complete frames. For normal use, this bit must be cleared to 0.
sourcepub fn set_brk(&mut self, val: bool)
pub fn set_brk(&mut self, val: bool)
Send break. If this bit is set to 1, a low-level is continually output on the UARTTXD output, after completing transmission of the current character. For the proper execution of the break command, the software must set this bit for at least two complete frames. For normal use, this bit must be cleared to 0.
sourcepub const fn pen(&self) -> bool
pub const fn pen(&self) -> bool
Parity enable: 0 = parity is disabled and no parity bit added to the data frame 1 = parity checking and generation is enabled.
sourcepub fn set_pen(&mut self, val: bool)
pub fn set_pen(&mut self, val: bool)
Parity enable: 0 = parity is disabled and no parity bit added to the data frame 1 = parity checking and generation is enabled.
sourcepub const fn eps(&self) -> bool
pub const fn eps(&self) -> bool
Even parity select. Controls the type of parity the UART uses during transmission and reception: 0 = odd parity. The UART generates or checks for an odd number of 1s in the data and parity bits. 1 = even parity. The UART generates or checks for an even number of 1s in the data and parity bits. This bit has no effect when the PEN bit disables parity checking and generation.
sourcepub fn set_eps(&mut self, val: bool)
pub fn set_eps(&mut self, val: bool)
Even parity select. Controls the type of parity the UART uses during transmission and reception: 0 = odd parity. The UART generates or checks for an odd number of 1s in the data and parity bits. 1 = even parity. The UART generates or checks for an even number of 1s in the data and parity bits. This bit has no effect when the PEN bit disables parity checking and generation.
sourcepub const fn stp2(&self) -> bool
pub const fn stp2(&self) -> bool
Two stop bits select. If this bit is set to 1, two stop bits are transmitted at the end of the frame. The receive logic does not check for two stop bits being received.
sourcepub fn set_stp2(&mut self, val: bool)
pub fn set_stp2(&mut self, val: bool)
Two stop bits select. If this bit is set to 1, two stop bits are transmitted at the end of the frame. The receive logic does not check for two stop bits being received.
sourcepub const fn fen(&self) -> bool
pub const fn fen(&self) -> bool
Enable FIFOs: 0 = FIFOs are disabled (character mode) that is, the FIFOs become 1-byte-deep holding registers 1 = transmit and receive FIFO buffers are enabled (FIFO mode).
sourcepub fn set_fen(&mut self, val: bool)
pub fn set_fen(&mut self, val: bool)
Enable FIFOs: 0 = FIFOs are disabled (character mode) that is, the FIFOs become 1-byte-deep holding registers 1 = transmit and receive FIFO buffers are enabled (FIFO mode).
sourcepub const fn wlen(&self) -> u8
pub const fn wlen(&self) -> u8
Word length. These bits indicate the number of data bits transmitted or received in a frame as follows: b11 = 8 bits b10 = 7 bits b01 = 6 bits b00 = 5 bits.
sourcepub fn set_wlen(&mut self, val: u8)
pub fn set_wlen(&mut self, val: u8)
Word length. These bits indicate the number of data bits transmitted or received in a frame as follows: b11 = 8 bits b10 = 7 bits b01 = 6 bits b00 = 5 bits.
sourcepub const fn sps(&self) -> bool
pub const fn sps(&self) -> bool
Stick parity select. 0 = stick parity is disabled 1 = either: * if the EPS bit is 0 then the parity bit is transmitted and checked as a 1 * if the EPS bit is 1 then the parity bit is transmitted and checked as a 0. This bit has no effect when the PEN bit disables parity checking and generation.
sourcepub fn set_sps(&mut self, val: bool)
pub fn set_sps(&mut self, val: bool)
Stick parity select. 0 = stick parity is disabled 1 = either: * if the EPS bit is 0 then the parity bit is transmitted and checked as a 1 * if the EPS bit is 1 then the parity bit is transmitted and checked as a 0. This bit has no effect when the PEN bit disables parity checking and generation.