Struct stm32_metapac::cec::regs::Cr

#[repr(transparent)]
pub struct Cr(pub u32);

CEC control register.

Tuple Fields

0: u32

Implementations

impl Cr

pub const fn cecen(&self) -> bool

CEC Enable The CECEN bit is set and cleared by software. CECEN=1 starts message reception and enables the TXSOM control. CECEN=0 disables the CEC peripheral, clears all bits of CEC_CR register and aborts any on-going reception or transmission.

pub fn set_cecen(&mut self, val: bool)

CEC Enable The CECEN bit is set and cleared by software. CECEN=1 starts message reception and enables the TXSOM control. CECEN=0 disables the CEC peripheral, clears all bits of CEC_CR register and aborts any on-going reception or transmission.

pub const fn txsom(&self) -> bool

Tx Start Of Message TXSOM is set by software to command transmission of the first byte of a CEC message. If the CEC message consists of only one byte, TXEOM must be set before of TXSOM. Start-Bit is effectively started on the CEC line after SFT is counted. If TXSOM is set while a message reception is ongoing, transmission will start after the end of reception. TXSOM is cleared by hardware after the last byte of the message is sent with a positive acknowledge (TXEND=1), in case of transmission underrun (TXUDR=1), negative acknowledge (TXACKE=1), and transmission error (TXERR=1). It is also cleared by CECEN=0. It is not cleared and transmission is automatically retried in case of arbitration lost (ARBLST=1). TXSOM can be also used as a status bit informing application whether any transmission request is pending or under execution. The application can abort a transmission request at any time by clearing the CECEN bit. Note: TXSOM must be set when CECEN=1 TXSOM must be set when transmission data is available into TXDR HEADERs first four bits containing own peripheral address are taken from TXDR[7:4], not from CEC_CFGR.OAR which is used only for reception.

pub fn set_txsom(&mut self, val: bool)

Tx Start Of Message TXSOM is set by software to command transmission of the first byte of a CEC message. If the CEC message consists of only one byte, TXEOM must be set before of TXSOM. Start-Bit is effectively started on the CEC line after SFT is counted. If TXSOM is set while a message reception is ongoing, transmission will start after the end of reception. TXSOM is cleared by hardware after the last byte of the message is sent with a positive acknowledge (TXEND=1), in case of transmission underrun (TXUDR=1), negative acknowledge (TXACKE=1), and transmission error (TXERR=1). It is also cleared by CECEN=0. It is not cleared and transmission is automatically retried in case of arbitration lost (ARBLST=1). TXSOM can be also used as a status bit informing application whether any transmission request is pending or under execution. The application can abort a transmission request at any time by clearing the CECEN bit. Note: TXSOM must be set when CECEN=1 TXSOM must be set when transmission data is available into TXDR HEADERs first four bits containing own peripheral address are taken from TXDR[7:4], not from CEC_CFGR.OAR which is used only for reception.

pub const fn txeom(&self) -> bool

Tx End Of Message The TXEOM bit is set by software to command transmission of the last byte of a CEC message. TXEOM is cleared by hardware at the same time and under the same conditions as for TXSOM. Note: TXEOM must be set when CECEN=1 TXEOM must be set before writing transmission data to TXDR If TXEOM is set when TXSOM=0, transmitted message will consist of 1 byte (HEADER) only (PING message).

pub fn set_txeom(&mut self, val: bool)

Tx End Of Message The TXEOM bit is set by software to command transmission of the last byte of a CEC message. TXEOM is cleared by hardware at the same time and under the same conditions as for TXSOM. Note: TXEOM must be set when CECEN=1 TXEOM must be set before writing transmission data to TXDR If TXEOM is set when TXSOM=0, transmitted message will consist of 1 byte (HEADER) only (PING message).

Trait Implementations

impl Clone for Cr

fn clone(&self) -> Cr

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Default for Cr

fn default() -> Cr

Returns the “default value” for a type.

impl PartialEq for Cr

fn eq(&self, other: &Cr) -> bool

Tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

Tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl Copy for Cr

impl Eq for Cr

impl StructuralPartialEq for Cr