stm32-metapac

Crates

git

Versions

stm32h523re

Flavors

Struct stm32_metapac::usb::regs::Istr

#[repr(transparent)]
pub struct Istr(pub u32);
Expand description

interrupt status register

Tuple Fields§

§0: u32

Implementations§

§

impl Istr

pub const fn ep_id(&self) -> u8

Device Endpoint / Host channel identification number These bits are written by the hardware according to the host channel or device endpoint number, which generated the interrupt request. If several endpoint/channel transactions are pending, the hardware writes the identification number related to the endpoint/channel having the highest priority defined in the following way: Two levels are defined, in order of priority: Isochronous and double-buffered bulk channels/endpoints are considered first and then the others are examined. If more than one endpoint/channel from the same set is requesting an interrupt, the IDN bits in USB_ISTR register are assigned according to the lowest requesting register, CHEP0R having the highest priority followed by CHEP1R and so on. The application software can assign a register to each endpoint/channel according to this priority scheme, so as to order the concurring endpoint/channel requests in a suitable way. These bits are read only.

pub fn set_ep_id(&mut self, val: u8)

Device Endpoint / Host channel identification number These bits are written by the hardware according to the host channel or device endpoint number, which generated the interrupt request. If several endpoint/channel transactions are pending, the hardware writes the identification number related to the endpoint/channel having the highest priority defined in the following way: Two levels are defined, in order of priority: Isochronous and double-buffered bulk channels/endpoints are considered first and then the others are examined. If more than one endpoint/channel from the same set is requesting an interrupt, the IDN bits in USB_ISTR register are assigned according to the lowest requesting register, CHEP0R having the highest priority followed by CHEP1R and so on. The application software can assign a register to each endpoint/channel according to this priority scheme, so as to order the concurring endpoint/channel requests in a suitable way. These bits are read only.

pub const fn dir(&self) -> Dir

Direction of transaction This bit is written by the hardware according to the direction of the successful transaction, which generated the interrupt request. If DIR bit=0, VTTX bit is set in the USB_EPnR register related to the interrupting endpoint. The interrupting transaction is of IN type (data transmitted by the USB peripheral to the host PC). If DIR bit=1, VTRX bit or both VTTX/VTRX are set in the USB_EPnR register related to the interrupting endpoint. The interrupting transaction is of OUT type (data received by the USB peripheral from the host PC) or two pending transactions are waiting to be processed. This information can be used by the application software to access the USB_EPnR bits related to the triggering transaction since it represents the direction having the interrupt pending. This bit is read-only.

pub fn set_dir(&mut self, val: Dir)

Direction of transaction This bit is written by the hardware according to the direction of the successful transaction, which generated the interrupt request. If DIR bit=0, VTTX bit is set in the USB_EPnR register related to the interrupting endpoint. The interrupting transaction is of IN type (data transmitted by the USB peripheral to the host PC). If DIR bit=1, VTRX bit or both VTTX/VTRX are set in the USB_EPnR register related to the interrupting endpoint. The interrupting transaction is of OUT type (data received by the USB peripheral from the host PC) or two pending transactions are waiting to be processed. This information can be used by the application software to access the USB_EPnR bits related to the triggering transaction since it represents the direction having the interrupt pending. This bit is read-only.

pub const fn l1req(&self) -> bool

LPM L1 state request This bit is set by the hardware when LPM command to enter the L1 state is successfully received and acknowledged. This bit is read/write but only ’0 can be written and writing ’1 has no effect.

pub fn set_l1req(&mut self, val: bool)

LPM L1 state request This bit is set by the hardware when LPM command to enter the L1 state is successfully received and acknowledged. This bit is read/write but only ’0 can be written and writing ’1 has no effect.

pub const fn esof(&self) -> bool

Expected start of frame This bit is set by the hardware when an SOF packet is expected but not received. The host sends an SOF packet each 1 ms, but if the device does not receive it properly, the Suspend Timer issues this interrupt. If three consecutive ESOF interrupts are generated (i.e. three SOF packets are lost) without any traffic occurring in between, a SUSP interrupt is generated. This bit is set even when the missing SOF packets occur while the Suspend Timer is not yet locked. This bit is read/write but only ’0 can be written and writing ’1 has no effect.

pub fn set_esof(&mut self, val: bool)

Expected start of frame This bit is set by the hardware when an SOF packet is expected but not received. The host sends an SOF packet each 1 ms, but if the device does not receive it properly, the Suspend Timer issues this interrupt. If three consecutive ESOF interrupts are generated (i.e. three SOF packets are lost) without any traffic occurring in between, a SUSP interrupt is generated. This bit is set even when the missing SOF packets occur while the Suspend Timer is not yet locked. This bit is read/write but only ’0 can be written and writing ’1 has no effect.

pub const fn sof(&self) -> bool

Start of frame This bit signals the beginning of a new USB frame and it is set when a SOF packet arrives through the USB bus. The interrupt service routine may monitor the SOF events to have a 1 ms synchronization event to the USB host and to safely read the USB_FNR register which is updated at the SOF packet reception (this could be useful for isochronous applications). This bit is read/write but only ’0 can be written and writing ’1 has no effect.

pub fn set_sof(&mut self, val: bool)

Start of frame This bit signals the beginning of a new USB frame and it is set when a SOF packet arrives through the USB bus. The interrupt service routine may monitor the SOF events to have a 1 ms synchronization event to the USB host and to safely read the USB_FNR register which is updated at the SOF packet reception (this could be useful for isochronous applications). This bit is read/write but only ’0 can be written and writing ’1 has no effect.

pub const fn reset(&self) -> bool

reset request Device mode This bit is set by hardware when an USB reset is released by the host and the bus returns to idle. USB reset state is internally detected after the sampling of 60 consecutive SE0 cycles. Host mode This bit is set by hardware when device connection or device disconnection is detected. Device connection is signaled after J state is sampled for 22cycles consecutively from unconnected state. Device disconnection is signaled after SE0 state is sampled for 22cycles consecutively from connected state.

pub fn set_reset(&mut self, val: bool)

reset request Device mode This bit is set by hardware when an USB reset is released by the host and the bus returns to idle. USB reset state is internally detected after the sampling of 60 consecutive SE0 cycles. Host mode This bit is set by hardware when device connection or device disconnection is detected. Device connection is signaled after J state is sampled for 22cycles consecutively from unconnected state. Device disconnection is signaled after SE0 state is sampled for 22cycles consecutively from connected state.

pub const fn susp(&self) -> bool

Suspend mode request This bit is set by the hardware when no traffic has been received for 3 ms, indicating a suspend mode request from the USB bus. The suspend condition check is enabled immediately after any USB reset and it is disabled by the hardware when the suspend mode is active (SUSPEN=1) until the end of resume sequence. This bit is read/write but only ’0 can be written and writing ’1 has no effect.

pub fn set_susp(&mut self, val: bool)

Suspend mode request This bit is set by the hardware when no traffic has been received for 3 ms, indicating a suspend mode request from the USB bus. The suspend condition check is enabled immediately after any USB reset and it is disabled by the hardware when the suspend mode is active (SUSPEN=1) until the end of resume sequence. This bit is read/write but only ’0 can be written and writing ’1 has no effect.

pub const fn wkup(&self) -> bool

Wakeup This bit is set to 1 by the hardware when, during suspend mode, activity is detected that wakes up the USB peripheral. This event asynchronously clears the LP_MODE bit in the CTLR register and activates the USB_WAKEUP line, which can be used to notify the rest of the device (e.g. wakeup unit) about the start of the resume process. This bit is read/write but only ’0 can be written and writing ’1 has no effect.

pub fn set_wkup(&mut self, val: bool)

Wakeup This bit is set to 1 by the hardware when, during suspend mode, activity is detected that wakes up the USB peripheral. This event asynchronously clears the LP_MODE bit in the CTLR register and activates the USB_WAKEUP line, which can be used to notify the rest of the device (e.g. wakeup unit) about the start of the resume process. This bit is read/write but only ’0 can be written and writing ’1 has no effect.

pub const fn err(&self) -> bool

Error This flag is set whenever one of the errors listed below has occurred: NANS: No ANSwer. The timeout for a host response has expired. CRC: Cyclic Redundancy Check error. One of the received CRCs, either in the token or in the data, was wrong. BST: Bit Stuffing error. A bit stuffing error was detected anywhere in the PID, data, and/or CRC. FVIO: Framing format Violation. A non-standard frame was received (EOP not in the right place, wrong token sequence, etc.). The USB software can usually ignore errors, since the USB peripheral and the PC host manage retransmission in case of errors in a fully transparent way. This interrupt can be useful during the software development phase, or to monitor the quality of transmission over the USB bus, to flag possible problems to the user (e.g. loose connector, too noisy environment, broken conductor in the USB cable and so on). This bit is read/write but only ’0 can be written and writing ’1 has no effect.

pub fn set_err(&mut self, val: bool)

Error This flag is set whenever one of the errors listed below has occurred: NANS: No ANSwer. The timeout for a host response has expired. CRC: Cyclic Redundancy Check error. One of the received CRCs, either in the token or in the data, was wrong. BST: Bit Stuffing error. A bit stuffing error was detected anywhere in the PID, data, and/or CRC. FVIO: Framing format Violation. A non-standard frame was received (EOP not in the right place, wrong token sequence, etc.). The USB software can usually ignore errors, since the USB peripheral and the PC host manage retransmission in case of errors in a fully transparent way. This interrupt can be useful during the software development phase, or to monitor the quality of transmission over the USB bus, to flag possible problems to the user (e.g. loose connector, too noisy environment, broken conductor in the USB cable and so on). This bit is read/write but only ’0 can be written and writing ’1 has no effect.

pub const fn pmaovr(&self) -> bool

Packet memory area over / underrun This bit is set if the microcontroller has not been able to respond in time to an USB memory request. The USB peripheral handles this event in the following way: During reception an ACK handshake packet is not sent, during transmission a bit-stuff error is forced on the transmitted stream; in both cases the host will retry the transaction. The PMAOVR interrupt should never occur during normal operations. Since the failed transaction is retried by the host, the application software has the chance to speed-up device operations during this interrupt handling, to be ready for the next transaction retry; however this does not happen during Isochronous transfers (no isochronous transaction is anyway retried) leading to a loss of data in this case. This bit is read/write but only ’0 can be written and writing ’1 has no effect.

pub fn set_pmaovr(&mut self, val: bool)

Packet memory area over / underrun This bit is set if the microcontroller has not been able to respond in time to an USB memory request. The USB peripheral handles this event in the following way: During reception an ACK handshake packet is not sent, during transmission a bit-stuff error is forced on the transmitted stream; in both cases the host will retry the transaction. The PMAOVR interrupt should never occur during normal operations. Since the failed transaction is retried by the host, the application software has the chance to speed-up device operations during this interrupt handling, to be ready for the next transaction retry; however this does not happen during Isochronous transfers (no isochronous transaction is anyway retried) leading to a loss of data in this case. This bit is read/write but only ’0 can be written and writing ’1 has no effect.

pub const fn ctr(&self) -> bool

Correct transfer This bit is set by the hardware to indicate that an endpoint/channel has successfully completed a transaction; using DIR and EP_ID bits software can determine which endpoint/channel requested the interrupt. This bit is read-only.

pub fn set_ctr(&mut self, val: bool)

Correct transfer This bit is set by the hardware to indicate that an endpoint/channel has successfully completed a transaction; using DIR and EP_ID bits software can determine which endpoint/channel requested the interrupt. This bit is read-only.

pub const fn thr512(&self) -> bool

512 byte threshold interrupt This bit is set to 1 by the hardware when 512 bytes have been transmitted or received during isochronous transfers. This bit is read/write but only 0 can be written and writing 1 has no effect. Note that no information is available to indicate the associated channel/endpoint, however in practice only one ISO endpoint/channel with such large packets can be supported, so that channel.

pub fn set_thr512(&mut self, val: bool)

512 byte threshold interrupt This bit is set to 1 by the hardware when 512 bytes have been transmitted or received during isochronous transfers. This bit is read/write but only 0 can be written and writing 1 has no effect. Note that no information is available to indicate the associated channel/endpoint, however in practice only one ISO endpoint/channel with such large packets can be supported, so that channel.

pub const fn dcon_stat(&self) -> bool

Device connection status Host mode: This bit contains information about device connection status. It is set by hardware when a LS/FS device is attached to the host while it is reset when the device is disconnected.

pub fn set_dcon_stat(&mut self, val: bool)

Device connection status Host mode: This bit contains information about device connection status. It is set by hardware when a LS/FS device is attached to the host while it is reset when the device is disconnected.

pub const fn ls_dcon(&self) -> bool

Low Speed device connected Host mode: This bit is set by hardware when an LS device connection is detected. Device connection is signaled after LS J-state is sampled for 22 consecutive cycles of the USB clock (48 MHz) from the unconnected state.

pub fn set_ls_dcon(&mut self, val: bool)

Low Speed device connected Host mode: This bit is set by hardware when an LS device connection is detected. Device connection is signaled after LS J-state is sampled for 22 consecutive cycles of the USB clock (48 MHz) from the unconnected state.

Trait Implementations§

§

impl Clone for Istr

§

fn clone(&self) -> Istr

Returns a copy of the value. Read more
1.0.0 · source§

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source. Read more
§

impl Default for Istr

§

fn default() -> Istr

Returns the “default value” for a type. Read more
§

impl PartialEq for Istr

§

fn eq(&self, other: &Istr) -> bool

Tests for self and other values to be equal, and is used by ==.
1.0.0 · source§

fn ne(&self, other: &Rhs) -> bool

Tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.
§

impl Copy for Istr

§

impl Eq for Istr

§

impl StructuralPartialEq for Istr

Auto Trait Implementations§

§

impl Freeze for Istr

§

impl RefUnwindSafe for Istr

§

impl Send for Istr

§

impl Sync for Istr

§

impl Unpin for Istr

§

impl UnwindSafe for Istr

Blanket Implementations§

source§

impl<T> Any for T
where T: 'static + ?Sized,

source§

fn type_id(&self) -> TypeId

Gets the TypeId of self. Read more
source§

impl<T> Borrow<T> for T
where T: ?Sized,

source§

fn borrow(&self) -> &T

Immutably borrows from an owned value. Read more
source§

impl<T> BorrowMut<T> for T
where T: ?Sized,

source§

fn borrow_mut(&mut self) -> &mut T

Mutably borrows from an owned value. Read more
source§

impl<T> CloneToUninit for T
where T: Clone,

source§

unsafe fn clone_to_uninit(&self, dst: *mut T)

🔬This is a nightly-only experimental API. (clone_to_uninit)
Performs copy-assignment from self to dst. Read more
source§

impl<T> From<T> for T

source§

fn from(t: T) -> T

Returns the argument unchanged.

source§

impl<T, U> Into<U> for T
where U: From<T>,

source§

fn into(self) -> U

Calls U::from(self).

That is, this conversion is whatever the implementation of From<T> for U chooses to do.

source§

impl<T, U> TryFrom<U> for T
where U: Into<T>,

source§

type Error = Infallible

The type returned in the event of a conversion error.
source§

fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>

Performs the conversion.
source§

impl<T, U> TryInto<U> for T
where U: TryFrom<T>,

source§

type Error = <U as TryFrom<T>>::Error

The type returned in the event of a conversion error.
source§

fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>

Performs the conversion.