Struct stm32_metapac::flash::regs::Optcr

#[repr(transparent)]
pub struct Optcr(pub u32);

FLASH option control register

Tuple Fields

0: u32

Implementations

impl Optcr

pub const fn optlock(&self) -> bool

FLASH_OPTCR lock option configuration bit The OPTLOCK bit locks the FLASH_OPTCR register as well as all _PRG registers. The correct write sequence to FLASH_OPTKEYR register unlocks this bit. If a wrong sequence is executed, or the unlock sequence to FLASH_OPTKEYR is performed twice, this bit remains locked until next system reset. It is possible to set OPTLOCK by programming it to 1. When set to 1, a new unlock sequence is mandatory to unlock it. When OPTLOCK changes from 0 to 1, the others bits of FLASH_OPTCR register do not change.

pub fn set_optlock(&mut self, val: bool)

FLASH_OPTCR lock option configuration bit The OPTLOCK bit locks the FLASH_OPTCR register as well as all _PRG registers. The correct write sequence to FLASH_OPTKEYR register unlocks this bit. If a wrong sequence is executed, or the unlock sequence to FLASH_OPTKEYR is performed twice, this bit remains locked until next system reset. It is possible to set OPTLOCK by programming it to 1. When set to 1, a new unlock sequence is mandatory to unlock it. When OPTLOCK changes from 0 to 1, the others bits of FLASH_OPTCR register do not change.

pub const fn optstrt(&self) -> bool

Option byte start change option configuration bit OPTSTRT triggers an option byte change operation. The user can set OPTSTRT only when the OPTLOCK bit is cleared to 0. It is set only by Software and cleared when the option byte change is completed or an error occurs (PGSERR or OPTCHANGEERR). It is reseted at the same time as BSY bit. The user application cannot modify any FLASH_XXX_PRG flash interface register until the option change operation has been completed. Before setting this bit, the user has to write the required values in the FLASH_XXX_PRG registers. The FLASH_XXX_PRG registers are locked until the option byte change operation has been executed in nonvolatile memory.

pub fn set_optstrt(&mut self, val: bool)

Option byte start change option configuration bit OPTSTRT triggers an option byte change operation. The user can set OPTSTRT only when the OPTLOCK bit is cleared to 0. It is set only by Software and cleared when the option byte change is completed or an error occurs (PGSERR or OPTCHANGEERR). It is reseted at the same time as BSY bit. The user application cannot modify any FLASH_XXX_PRG flash interface register until the option change operation has been completed. Before setting this bit, the user has to write the required values in the FLASH_XXX_PRG registers. The FLASH_XXX_PRG registers are locked until the option byte change operation has been executed in nonvolatile memory.

pub const fn swap_bank(&self) -> OptcrSwapBank

Bank swapping option configuration bit SWAP_BANK controls whether Bank1 and Bank2 are swapped or not. This bit is loaded with the SWAP_BANK bit of FLASH_OPTSR_CUR register only after reset or POR.

pub fn set_swap_bank(&mut self, val: OptcrSwapBank)

Bank swapping option configuration bit SWAP_BANK controls whether Bank1 and Bank2 are swapped or not. This bit is loaded with the SWAP_BANK bit of FLASH_OPTSR_CUR register only after reset or POR.

Trait Implementations

impl Clone for Optcr

fn clone(&self) -> Optcr

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Default for Optcr

fn default() -> Optcr

Returns the “default value” for a type.

impl PartialEq for Optcr

fn eq(&self, other: &Optcr) -> bool

This method tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

This method tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl Copy for Optcr

impl Eq for Optcr

impl StructuralEq for Optcr

impl StructuralPartialEq for Optcr