Struct stm32_metapac::pwr::regs::Apcr

#[repr(transparent)]
pub struct Apcr(pub u32);

PWR apply pull configuration register.

Tuple Fields

0: u32

Implementations

impl Apcr

pub const fn apc(&self) -> bool

Apply pull-up and pull-down configuration When this bit is set, the I/O pull-up and pull-down configurations defined in PO5_PUPD, PN7_PUPD bits and PUCRx, PDCRx registers are applied in Standby mode even after wakeup until APC bit is reset to 0. When this bit is cleared, the I/O pull-up or pull-down configurations defined in PO5_PUPD, PN7_PUPD bits and PUCRx and PDCRx registers are not applied in Standby mode and IO becomes Hi-Z.

pub fn set_apc(&mut self, val: bool)

Apply pull-up and pull-down configuration When this bit is set, the I/O pull-up and pull-down configurations defined in PO5_PUPD, PN7_PUPD bits and PUCRx, PDCRx registers are applied in Standby mode even after wakeup until APC bit is reset to 0. When this bit is cleared, the I/O pull-up or pull-down configurations defined in PO5_PUPD, PN7_PUPD bits and PUCRx and PDCRx registers are not applied in Standby mode and IO becomes Hi-Z.

pub const fn pn7_pupd(&self) -> bool

Port N bit 7 pull-up/down configuration When this bit is set, a weak pull-up or pull-down resistor is applied on PN7 following inverse logic applied on PN6. If the PUN6 bit in PWR_PUCRN register is set and APC bit is set the week pull-down is applied on PN7. If the PDN6 bit in PWR_PDCRN register is set and APC bit is set the week pull-up is applied on PN7.

pub fn set_pn7_pupd(&mut self, val: bool)

Port N bit 7 pull-up/down configuration When this bit is set, a weak pull-up or pull-down resistor is applied on PN7 following inverse logic applied on PN6. If the PUN6 bit in PWR_PUCRN register is set and APC bit is set the week pull-down is applied on PN7. If the PDN6 bit in PWR_PDCRN register is set and APC bit is set the week pull-up is applied on PN7.

pub const fn po5_pupd(&self) -> bool

Port O bit 5 pull-up/down configuration When this bit is set, a weak pull-up or pull down resistor is applied on PO5 following inverse logic applied on PO4. If the PUO4 bit in PWR_PUCRO register is set and APC bit is set the week pull-down is applied on PO5. If the PDO4 bit in PWR_PDCRO register is set and APC bit is set the week pull-up is applied on PO5..

pub fn set_po5_pupd(&mut self, val: bool)

Port O bit 5 pull-up/down configuration When this bit is set, a weak pull-up or pull down resistor is applied on PO5 following inverse logic applied on PO4. If the PUO4 bit in PWR_PUCRO register is set and APC bit is set the week pull-down is applied on PO5. If the PDO4 bit in PWR_PDCRO register is set and APC bit is set the week pull-up is applied on PO5..

pub const fn i3cpb6_pu(&self) -> bool

Port PB6 I3C pull-up bit When I3C is used on PB6, when set, this bit activates the pull-up on I3C1_SCL (PB6) in standby mode.

pub fn set_i3cpb6_pu(&mut self, val: bool)

Port PB6 I3C pull-up bit When I3C is used on PB6, when set, this bit activates the pull-up on I3C1_SCL (PB6) in standby mode.

pub const fn i3cpb7_pu(&self) -> bool

Port PB7 I3C pull-up bit When I3C is used on PB7, when set, this bit activates the pull-up on I3C1_SDA (PB7) in standby mode.

pub fn set_i3cpb7_pu(&mut self, val: bool)

Port PB7 I3C pull-up bit When I3C is used on PB7, when set, this bit activates the pull-up on I3C1_SDA (PB7) in standby mode.

pub const fn i3cpb8_pu(&self) -> bool

Port PB8 I3C pull-up bit When I3C is used on PB8, when set, this bit activates the pull-up on I3C1_SCL (PB8) in standby mode.

pub fn set_i3cpb8_pu(&mut self, val: bool)

Port PB8 I3C pull-up bit When I3C is used on PB8, when set, this bit activates the pull-up on I3C1_SCL (PB8) in standby mode.

pub const fn i3cpb9_pu(&self) -> bool

Port PB9 I3C pull-up bit When I3C is used on PB9, when set, this bit activates the pull-up on I3C1_SDA (PB9) in standby mode.

pub fn set_i3cpb9_pu(&mut self, val: bool)

Port PB9 I3C pull-up bit When I3C is used on PB9, when set, this bit activates the pull-up on I3C1_SDA (PB9) in standby mode.

Trait Implementations

impl Clone for Apcr

fn clone(&self) -> Apcr

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Default for Apcr

fn default() -> Apcr

Returns the “default value” for a type.

impl PartialEq for Apcr

fn eq(&self, other: &Apcr) -> bool

This method tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

This method tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl Copy for Apcr

impl Eq for Apcr

impl StructuralEq for Apcr

impl StructuralPartialEq for Apcr