Struct stm32_metapac::opamp::regs::Csr

#[repr(transparent)]
pub struct Csr(pub u32);

OPAMP control/status register.

Tuple Fields

0: u32

Implementations

impl Csr

pub const fn opampen(&self) -> bool

Operational amplifier Enable.

pub fn set_opampen(&mut self, val: bool)

Operational amplifier Enable.

pub const fn opalpm(&self) -> Opalpm

Operational amplifier Low Power Mode. The operational amplifier must be disable to change this configuration.

pub fn set_opalpm(&mut self, val: Opalpm)

Operational amplifier Low Power Mode. The operational amplifier must be disable to change this configuration.

pub const fn opamode(&self) -> Opamode

Operational amplifier PGA mode.

pub fn set_opamode(&mut self, val: Opamode)

Operational amplifier PGA mode.

pub const fn pga_gain(&self) -> PgaGain

Operational amplifier Programmable amplifier gain value.

pub fn set_pga_gain(&mut self, val: PgaGain)

Operational amplifier Programmable amplifier gain value.

pub const fn vm_sel(&self) -> VmSel

Inverting input selection. These bits are used only when OPAMODE = 00, 01 or 10. 1x: Inverting input not externally connected. These configurations are valid only when OPAMODE = 10 (PGA mode).

pub fn set_vm_sel(&mut self, val: VmSel)

Inverting input selection. These bits are used only when OPAMODE = 00, 01 or 10. 1x: Inverting input not externally connected. These configurations are valid only when OPAMODE = 10 (PGA mode).

pub const fn vp_sel(&self) -> VpSel

Non inverted input selection.

pub fn set_vp_sel(&mut self, val: VpSel)

Non inverted input selection.

pub const fn calon(&self) -> Calon

Calibration mode enabled.

pub fn set_calon(&mut self, val: Calon)

Calibration mode enabled.

pub const fn calsel(&self) -> Calsel

Calibration selection.

pub fn set_calsel(&mut self, val: Calsel)

Calibration selection.

pub const fn usertrim(&self) -> Usertrim

allows to switch from factory AOP offset trimmed values to AOP offset user trimmed values This bit is active for both mode normal and low-power.

pub fn set_usertrim(&mut self, val: Usertrim)

allows to switch from factory AOP offset trimmed values to AOP offset user trimmed values This bit is active for both mode normal and low-power.

pub const fn calout(&self) -> bool

Operational amplifier calibration output During calibration mode offset is trimmed when this signal toggle.

pub fn set_calout(&mut self, val: bool)

Operational amplifier calibration output During calibration mode offset is trimmed when this signal toggle.

pub const fn opa_range(&self) -> OpaRange

Operational amplifier power supply range for stability All AOP must be in power down to allow AOP-RANGE bit write. It applies to all AOP embedded in the product.

pub fn set_opa_range(&mut self, val: OpaRange)

Operational amplifier power supply range for stability All AOP must be in power down to allow AOP-RANGE bit write. It applies to all AOP embedded in the product.

Trait Implementations

impl Clone for Csr

fn clone(&self) -> Csr

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Default for Csr

fn default() -> Csr

Returns the “default value” for a type.

impl PartialEq for Csr

fn eq(&self, other: &Csr) -> bool

This method tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

This method tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl Copy for Csr

impl Eq for Csr

impl StructuralEq for Csr

impl StructuralPartialEq for Csr