Struct stm32_metapac::rcc::regs::Ccipr2

#[repr(transparent)]
pub struct Ccipr2(pub u32);

RCC peripherals independent clock configuration register 2

Tuple Fields

0: u32

Implementations

impl Ccipr2

pub const fn mdf1sel(&self) -> Mdfsel

MDF1 kernel clock source selection These bits are used to select the MDF1 kernel clock source. others: reserved

pub fn set_mdf1sel(&mut self, val: Mdfsel)

MDF1 kernel clock source selection These bits are used to select the MDF1 kernel clock source. others: reserved

pub const fn sai1sel(&self) -> Saisel

SAI1 kernel clock source selection These bits are used to select the SAI1 kernel clock source. others: reserved Note: If the selected clock is the external clock and this clock is stopped, a switch to another clock is impossible.

pub fn set_sai1sel(&mut self, val: Saisel)

SAI1 kernel clock source selection These bits are used to select the SAI1 kernel clock source. others: reserved Note: If the selected clock is the external clock and this clock is stopped, a switch to another clock is impossible.

pub const fn sai2sel(&self) -> Saisel

SAI2 kernel clock source selection These bits are used to select the SAI2 kernel clock source. others: reserved Note: If the selected clock is the external clock and this clock is stopped, a switch to another clock is impossible.

pub fn set_sai2sel(&mut self, val: Saisel)

SAI2 kernel clock source selection These bits are used to select the SAI2 kernel clock source. others: reserved Note: If the selected clock is the external clock and this clock is stopped, a switch to another clock is impossible.

pub const fn saessel(&self) -> Saessel

SAES kernel clock source selection This bit is used to select the SAES kernel clock source.

pub fn set_saessel(&mut self, val: Saessel)

SAES kernel clock source selection This bit is used to select the SAES kernel clock source.

pub const fn rngsel(&self) -> Rngsel

RNGSEL kernel clock source selection These bits are used to select the RNG kernel clock source.

pub fn set_rngsel(&mut self, val: Rngsel)

RNGSEL kernel clock source selection These bits are used to select the RNG kernel clock source.

pub const fn sdmmcsel(&self) -> Sdmmcsel

SDMMC1 and SDMMC2 kernel clock source selection This bit is used to select the SDMMC kernel clock source. It is recommended to change this bit only after reset and before enabling the SDMMC.

pub fn set_sdmmcsel(&mut self, val: Sdmmcsel)

SDMMC1 and SDMMC2 kernel clock source selection This bit is used to select the SDMMC kernel clock source. It is recommended to change this bit only after reset and before enabling the SDMMC.

pub const fn dsisel(&self) -> Dsisel

DSI kernel clock source selection This bit is used to select the DSI kernel clock source. This bit is only available on some devices in the STM32U5 Series. Refer to the device datasheet for availability of its associated peripheral. Note: If not present, consider this bit as reserved and keep it at reset value.

pub fn set_dsisel(&mut self, val: Dsisel)

DSI kernel clock source selection This bit is used to select the DSI kernel clock source. This bit is only available on some devices in the STM32U5 Series. Refer to the device datasheet for availability of its associated peripheral. Note: If not present, consider this bit as reserved and keep it at reset value.

pub const fn usart6sel(&self) -> Usartsel

USART6 kernel clock source selection These bits are used to select the USART6 kernel clock source. The USART6 is functional in Stop 0 and Stop 1 modes only when the kernel clock is HSI or LSE. Note: This bitfield is only available on some devices in the STM32U5 Series. Refer to the device datasheet for availability of its associated peripheral. If not present, consider this bitfield as reserved and keep it at reset value.

pub fn set_usart6sel(&mut self, val: Usartsel)

USART6 kernel clock source selection These bits are used to select the USART6 kernel clock source. The USART6 is functional in Stop 0 and Stop 1 modes only when the kernel clock is HSI or LSE. Note: This bitfield is only available on some devices in the STM32U5 Series. Refer to the device datasheet for availability of its associated peripheral. If not present, consider this bitfield as reserved and keep it at reset value.

pub const fn ltdcsel(&self) -> Ltdcsel

LTDC kernel clock source selection This bit is used to select the LTDC kernel clock source. Note: This bit is only available on some devices in the STM32U5 Series. Refer to the device datasheet for availability of its associated peripheral. If not present, consider this bit as reserved and keep it at reset value.

pub fn set_ltdcsel(&mut self, val: Ltdcsel)

LTDC kernel clock source selection This bit is used to select the LTDC kernel clock source. Note: This bit is only available on some devices in the STM32U5 Series. Refer to the device datasheet for availability of its associated peripheral. If not present, consider this bit as reserved and keep it at reset value.

pub const fn octospisel(&self) -> Octospisel

OCTOSPI1 and OCTOSPI2 kernel clock source selection These bits are used to select the OCTOSPI1 and OCTOSPI2 kernel clock source.

pub fn set_octospisel(&mut self, val: Octospisel)

OCTOSPI1 and OCTOSPI2 kernel clock source selection These bits are used to select the OCTOSPI1 and OCTOSPI2 kernel clock source.

pub const fn hspi1sel(&self) -> Hspisel

HSPI1 kernel clock source selection These bits are used to select the HSPI1 kernel clock source. Note: This bitfield is only available on some devices in the STM32U5 Series. Refer to the device datasheet for availability of its associated peripheral. If not present, consider this bitfield as reserved and keep it at reset value.

pub fn set_hspi1sel(&mut self, val: Hspisel)

HSPI1 kernel clock source selection These bits are used to select the HSPI1 kernel clock source. Note: This bitfield is only available on some devices in the STM32U5 Series. Refer to the device datasheet for availability of its associated peripheral. If not present, consider this bitfield as reserved and keep it at reset value.

pub const fn i2c5sel(&self) -> I2csel

I2C5 kernel clock source selection These bits are used to select the I2C5 kernel clock source. The I2C5 is functional in Stop 0 and Stop 1 modes only when the kernel clock is HSI�or MSIK. Note: This bitfield is only available on some devices in the STM32U5 Series. Refer to the device datasheet for availability of its associated peripheral. If not present, consider this bitfield as reserved and keep it at reset value.

pub fn set_i2c5sel(&mut self, val: I2csel)

I2C5 kernel clock source selection These bits are used to select the I2C5 kernel clock source. The I2C5 is functional in Stop 0 and Stop 1 modes only when the kernel clock is HSI�or MSIK. Note: This bitfield is only available on some devices in the STM32U5 Series. Refer to the device datasheet for availability of its associated peripheral. If not present, consider this bitfield as reserved and keep it at reset value.

pub const fn i2c6sel(&self) -> I2csel

I2C6 kernel clock source selection These bits are used to select the I2C6 kernel clock source. The I2C6 is functional in Stop 0 and Stop 1 modes only when the kernel clock is HSI�or MSIK. Note: This bitfield is only available on some devices in the STM32U5 Series. Refer to the device datasheet for availability of its associated peripheral. If not present, consider this bitfield as reserved and keep it at reset value.

pub fn set_i2c6sel(&mut self, val: I2csel)

I2C6 kernel clock source selection These bits are used to select the I2C6 kernel clock source. The I2C6 is functional in Stop 0 and Stop 1 modes only when the kernel clock is HSI�or MSIK. Note: This bitfield is only available on some devices in the STM32U5 Series. Refer to the device datasheet for availability of its associated peripheral. If not present, consider this bitfield as reserved and keep it at reset value.

pub const fn otghssel(&self) -> Otghssel

OTG_HS PHY kernel clock source selection These bits are used to select the OTG_HS PHY kernel clock source. Note: This bitfield is only available on some devices in the STM32U5 Series. Refer to the device datasheet for availability of its associated peripheral. If not present, consider this bitfield as reserved and keep it at reset value.

pub fn set_otghssel(&mut self, val: Otghssel)

OTG_HS PHY kernel clock source selection These bits are used to select the OTG_HS PHY kernel clock source. Note: This bitfield is only available on some devices in the STM32U5 Series. Refer to the device datasheet for availability of its associated peripheral. If not present, consider this bitfield as reserved and keep it at reset value.

Trait Implementations

impl Clone for Ccipr2

fn clone(&self) -> Ccipr2

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Default for Ccipr2

fn default() -> Ccipr2

Returns the “default value” for a type.

impl PartialEq for Ccipr2

fn eq(&self, other: &Ccipr2) -> bool

This method tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

This method tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl Copy for Ccipr2

impl Eq for Ccipr2

impl StructuralEq for Ccipr2

impl StructuralPartialEq for Ccipr2