stm32-metapac

Crates

git

Versions

stm32u575ag

Flavors

Struct stm32_metapac::rcc::regs::Icscr1

#[repr(transparent)]
pub struct Icscr1(pub u32);
Expand description

RCC internal clock sources calibration register 1

Tuple Fields§

§0: u32

Implementations§

§

impl Icscr1

pub const fn msical3(&self) -> u8

MSIRC3 clock calibration for MSI ranges 12 to 15 These bits are initialized at startup with the factory-programmed MSIRC3 calibration trim value for ranges 12 to 15. When MSITRIM3 is written, MSICAL3 is updated with the sum of MSITRIM3[4:0] and the factory calibration trim value MSIRC2[4:0]. There is no hardware protection to limit a potential overflow due to the addition of MSITRIM bitfield and factory program bitfield for this calibration value. Control must be managed by software at user level.

pub fn set_msical3(&mut self, val: u8)

MSIRC3 clock calibration for MSI ranges 12 to 15 These bits are initialized at startup with the factory-programmed MSIRC3 calibration trim value for ranges 12 to 15. When MSITRIM3 is written, MSICAL3 is updated with the sum of MSITRIM3[4:0] and the factory calibration trim value MSIRC2[4:0]. There is no hardware protection to limit a potential overflow due to the addition of MSITRIM bitfield and factory program bitfield for this calibration value. Control must be managed by software at user level.

pub const fn msical2(&self) -> u8

MSIRC2 clock calibration for MSI ranges 8 to 11 These bits are initialized at startup with the factory-programmed MSIRC2 calibration trim value for ranges 8 to 11. When MSITRIM2 is written, MSICAL2 is updated with the sum of MSITRIM2[4:0] and the factory calibration trim value MSIRC2[4:0]. There is no hardware protection to limit a potential overflow due to the addition of MSITRIM bitfield and factory program bitfield for this calibration value. Control must be managed by software at user level.

pub fn set_msical2(&mut self, val: u8)

MSIRC2 clock calibration for MSI ranges 8 to 11 These bits are initialized at startup with the factory-programmed MSIRC2 calibration trim value for ranges 8 to 11. When MSITRIM2 is written, MSICAL2 is updated with the sum of MSITRIM2[4:0] and the factory calibration trim value MSIRC2[4:0]. There is no hardware protection to limit a potential overflow due to the addition of MSITRIM bitfield and factory program bitfield for this calibration value. Control must be managed by software at user level.

pub const fn msical1(&self) -> u8

MSIRC1 clock calibration for MSI ranges 4 to 7 These bits are initialized at startup with the factory-programmed MSIRC1 calibration trim value for ranges 4 to 7. When MSITRIM1 is written, MSICAL1 is updated with the sum of MSITRIM1[4:0] and the factory calibration trim value MSIRC1[4:0]. There is no hardware protection to limit a potential overflow due to the addition of MSITRIM bitfield and factory program bitfield for this calibration value. Control must be managed by software at user level.

pub fn set_msical1(&mut self, val: u8)

MSIRC1 clock calibration for MSI ranges 4 to 7 These bits are initialized at startup with the factory-programmed MSIRC1 calibration trim value for ranges 4 to 7. When MSITRIM1 is written, MSICAL1 is updated with the sum of MSITRIM1[4:0] and the factory calibration trim value MSIRC1[4:0]. There is no hardware protection to limit a potential overflow due to the addition of MSITRIM bitfield and factory program bitfield for this calibration value. Control must be managed by software at user level.

pub const fn msical0(&self) -> u8

MSIRC0 clock calibration for MSI ranges 0 to 3 These bits are initialized at startup with the factory-programmed MSIRC0 calibration trim value for ranges 0 to 3. When MSITRIM0 is written, MSICAL0 is updated with the sum of MSITRIM0[4:0] and the factory-programmed calibration trim value MSIRC0[4:0].

pub fn set_msical0(&mut self, val: u8)

MSIRC0 clock calibration for MSI ranges 0 to 3 These bits are initialized at startup with the factory-programmed MSIRC0 calibration trim value for ranges 0 to 3. When MSITRIM0 is written, MSICAL0 is updated with the sum of MSITRIM0[4:0] and the factory-programmed calibration trim value MSIRC0[4:0].

pub const fn msibias(&self) -> Msibias

MSI bias mode selection Set by software to select the MSI bias mode. By default, the MSI bias is in continuous mode in order to maintain the output clocks accuracy. Setting this bit reduces the MSI consumption under range 4 but decrease its accuracy.

pub fn set_msibias(&mut self, val: Msibias)

MSI bias mode selection Set by software to select the MSI bias mode. By default, the MSI bias is in continuous mode in order to maintain the output clocks accuracy. Setting this bit reduces the MSI consumption under range 4 but decrease its accuracy.

pub const fn msirgsel(&self) -> Msirgsel

MSI clock range selection Set by software to select the MSIS and MSIK clocks range with MSISRANGE[3:0] and MSIKRANGE[3:0]. Write 0 has no effect. After exiting Standby or Shutdown mode, or after a reset, this bit is at 0 and the MSIS and MSIK ranges are provided by MSISSRANGE[3:0] and MSIKSRANGE[3:0] in RCC_CSR.

pub fn set_msirgsel(&mut self, val: Msirgsel)

MSI clock range selection Set by software to select the MSIS and MSIK clocks range with MSISRANGE[3:0] and MSIKRANGE[3:0]. Write 0 has no effect. After exiting Standby or Shutdown mode, or after a reset, this bit is at 0 and the MSIS and MSIK ranges are provided by MSISSRANGE[3:0] and MSIKSRANGE[3:0] in RCC_CSR.

pub const fn msikrange(&self) -> Msirange

MSIK clock ranges These bits are configured by software to choose the frequency range of MSIK oscillator when MSIRGSEL is set. 16 frequency ranges are available: Note: MSIKRANGE can be modified when MSIK is OFF (MSISON = 0) or when MSIK is ready (MSIKRDY = 1). MSIKRANGE must NOT be modified when MSIK is ON and NOT ready (MSIKON = 1 and MSIKRDY = 0) MSIKRANGE is kept when the device wakes up from Stop mode, except when the MSIK range is above 24 MHz. In this case MSIKRANGE is changed by hardware into Range 2 (24 MHz).

pub fn set_msikrange(&mut self, val: Msirange)

MSIK clock ranges These bits are configured by software to choose the frequency range of MSIK oscillator when MSIRGSEL is set. 16 frequency ranges are available: Note: MSIKRANGE can be modified when MSIK is OFF (MSISON = 0) or when MSIK is ready (MSIKRDY = 1). MSIKRANGE must NOT be modified when MSIK is ON and NOT ready (MSIKON = 1 and MSIKRDY = 0) MSIKRANGE is kept when the device wakes up from Stop mode, except when the MSIK range is above 24 MHz. In this case MSIKRANGE is changed by hardware into Range 2 (24 MHz).

pub const fn msisrange(&self) -> Msirange

MSIS clock ranges These bits are configured by software to choose the frequency range of MSIS oscillator when MSIRGSEL is set. 16 frequency ranges are available: Note: MSISRANGE can be modified when MSIS is OFF (MSISON = 0) or when MSIS is ready (MSISRDY = 1). MSISRANGE must NOT be modified when MSIS is ON and NOT ready (MSISON = 1 and MSISRDY = 0) MSISRANGE is kept when the device wakes up from Stop mode, except when the MSIS range is above 24 MHz. In this case MSISRANGE is changed by hardware into Range 2 (24 MHz).

pub fn set_msisrange(&mut self, val: Msirange)

MSIS clock ranges These bits are configured by software to choose the frequency range of MSIS oscillator when MSIRGSEL is set. 16 frequency ranges are available: Note: MSISRANGE can be modified when MSIS is OFF (MSISON = 0) or when MSIS is ready (MSISRDY = 1). MSISRANGE must NOT be modified when MSIS is ON and NOT ready (MSISON = 1 and MSISRDY = 0) MSISRANGE is kept when the device wakes up from Stop mode, except when the MSIS range is above 24 MHz. In this case MSISRANGE is changed by hardware into Range 2 (24 MHz).

Trait Implementations§

§

impl Clone for Icscr1

§

fn clone(&self) -> Icscr1

Returns a copy of the value. Read more
1.0.0 · source§

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source. Read more
§

impl Default for Icscr1

§

fn default() -> Icscr1

Returns the “default value” for a type. Read more
§

impl PartialEq for Icscr1

§

fn eq(&self, other: &Icscr1) -> bool

Tests for self and other values to be equal, and is used by ==.
1.0.0 · source§

fn ne(&self, other: &Rhs) -> bool

Tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.
§

impl Copy for Icscr1

§

impl Eq for Icscr1

§

impl StructuralPartialEq for Icscr1

Auto Trait Implementations§

§

impl Freeze for Icscr1

§

impl RefUnwindSafe for Icscr1

§

impl Send for Icscr1

§

impl Sync for Icscr1

§

impl Unpin for Icscr1

§

impl UnwindSafe for Icscr1

Blanket Implementations§

source§

impl<T> Any for T
where T: 'static + ?Sized,

source§

fn type_id(&self) -> TypeId

Gets the TypeId of self. Read more
source§

impl<T> Borrow<T> for T
where T: ?Sized,

source§

fn borrow(&self) -> &T

Immutably borrows from an owned value. Read more
source§

impl<T> BorrowMut<T> for T
where T: ?Sized,

source§

fn borrow_mut(&mut self) -> &mut T

Mutably borrows from an owned value. Read more
source§

impl<T> CloneToUninit for T
where T: Clone,

source§

unsafe fn clone_to_uninit(&self, dst: *mut T)

🔬This is a nightly-only experimental API. (clone_to_uninit)
Performs copy-assignment from self to dst. Read more
source§

impl<T> From<T> for T

source§

fn from(t: T) -> T

Returns the argument unchanged.

source§

impl<T, U> Into<U> for T
where U: From<T>,

source§

fn into(self) -> U

Calls U::from(self).

That is, this conversion is whatever the implementation of From<T> for U chooses to do.

source§

impl<T, U> TryFrom<U> for T
where U: Into<T>,

source§

type Error = Infallible

The type returned in the event of a conversion error.
source§

fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>

Performs the conversion.
source§

impl<T, U> TryInto<U> for T
where U: TryFrom<T>,

source§

type Error = <U as TryFrom<T>>::Error

The type returned in the event of a conversion error.
source§

fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>

Performs the conversion.