Enum Opcode 

#[repr(u8)]
pub enum Opcode {
    Terminate = 0,
    _RESERVED_1 = 1,
    _RESERVED_2 = 2,
    _RESERVED_3 = 3,
    AddInc = 4,
    SubDecNeg = 5,
    ModAddInc = 6,
    ModSubDecNeg = 7,
    Andtst0clr0 = 8,
    Orcopyset0 = 9,
    Xorflp0invcmp = 10,
    _RESERVED_b = 11,
    Shr0 = 12,
    Shr1 = 13,
    Shl0 = 14,
    Shl1 = 15,
    MulLow = 16,
    ModMul = 17,
    ModMulN = 18,
    ModExp = 19,
    Division = 20,
    ModInv = 21,
    ModDiv = 22,
    MulHigh = 23,
    ModMlac = 24,
    ModMlacnr = 25,
    _RESERVED_1a = 26,
    Reduction = 27,
    _RESERVED_1c = 28,
    _RESERVED_1d = 29,
    _RESERVED_1e = 30,
    _RESERVED_1f = 31,
}

Variants

Terminate = 0

Terminate operation.

_RESERVED_1 = 1

_RESERVED_2 = 2

_RESERVED_3 = 3

AddInc = 4

Add or Increment.

SubDecNeg = 5

Subtract, Decrement, or Negate.

ModAddInc = 6

Modular Add or Modular Increment.

ModSubDecNeg = 7

Modular Subtract, Modular Decrement, or Modular Negate.

Andtst0clr0 = 8

Perform AND, test, or clear.

Orcopyset0 = 9

Perform OR, copy, or set bits.

Xorflp0invcmp = 10

Perform XOR, flip bits, invert, or compare.

_RESERVED_b = 11

Shr0 = 12

Shift right 0 operation.

Shr1 = 13

Shift right 1 operation.

Shl0 = 14

Shift left 0 operation.

Shl1 = 15

Shift left 1 operation.

MulLow = 16

Multiply low operation.

ModMul = 17

Modular multiply operation.

ModMulN = 18

Modular multiply N operation.

ModExp = 19

Modular exponentiation operation.

Division = 20

Division operation.

ModInv = 21

Modular inversion operation.

ModDiv = 22

Modular division operation.

MulHigh = 23

Multiply high operation.

ModMlac = 24

Modular multiplication acceleration.

ModMlacnr = 25

Modular multiplication acceleration where final reduction is omitted.

_RESERVED_1a = 26

Reduction = 27

Reduction operation.

_RESERVED_1c = 28

_RESERVED_1d = 29

_RESERVED_1e = 30

_RESERVED_1f = 31

Implementations

impl Opcode

pub const fn from_bits(val: u8) -> Opcode

pub const fn to_bits(self) -> u8

Trait Implementations

impl Clone for Opcode

fn clone(&self) -> Opcode

Returns a duplicate of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for Opcode

fn fmt(&self, f: &mut Formatter<'_>) -> Result<(), Error>

Formats the value using the given formatter.

impl From<u8> for Opcode

fn from(val: u8) -> Opcode

Converts to this type from the input type.

impl Ord for Opcode

fn cmp(&self, other: &Opcode) -> Ordering

This method returns an Ordering between self and other.

fn max(self, other: Self) -> Self

where Self: Sized,

Compares and returns the maximum of two values.

fn min(self, other: Self) -> Self

where Self: Sized,

Compares and returns the minimum of two values.

fn clamp(self, min: Self, max: Self) -> Self

where Self: Sized,

Restrict a value to a certain interval.

impl PartialEq for Opcode

fn eq(&self, other: &Opcode) -> bool

Tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

Tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl PartialOrd for Opcode

fn partial_cmp(&self, other: &Opcode) -> Option<Ordering>

This method returns an ordering between self and other values if one exists.

fn lt(&self, other: &Rhs) -> bool

Tests less than (for self and other) and is used by the < operator.

fn le(&self, other: &Rhs) -> bool

Tests less than or equal to (for self and other) and is used by the <= operator.

fn gt(&self, other: &Rhs) -> bool

Tests greater than (for self and other) and is used by the > operator.

fn ge(&self, other: &Rhs) -> bool

Tests greater than or equal to (for self and other) and is used by the >= operator.

impl Copy for Opcode

impl Eq for Opcode

impl StructuralPartialEq for Opcode