embassy-rp

Crates

git

Versions

rp235xa

Flavors

Skip to main content

OutputOpenDrain

Struct OutputOpenDrain 

Source
pub struct OutputOpenDrain<'d, M: Mode = Blocking> { /* private fields */ }
Expand description

GPIO output open-drain.

Implementations§

Source§

impl<'d> OutputOpenDrain<'d, Blocking>

Source

pub fn new(pin: Peri<'d, impl Pin>, initial_output: Level) -> Self

Create a blocking GPIO output driver for a Pin in open drain mode with the provided Level.

Source§

impl<'d> OutputOpenDrain<'d, Async>

Source

pub fn new_async<T: Pin>( pin: Peri<'d, T>, irq: impl Binding<T::Interrupt, InterruptHandler<T>> + 'd, initial_output: Level, ) -> Self

Create an async GPIO output driver for a Pin in open drain mode with the provided Level.

The pin’s interrupt must be bound to InterruptHandler for this pin.

Source

pub async fn wait_for_high(&mut self)

Wait until the pin is high. If it is already high, return immediately.

Source

pub async fn wait_for_low(&mut self)

Wait until the pin is low. If it is already low, return immediately.

Source

pub async fn wait_for_rising_edge(&mut self)

Wait for the pin to undergo a transition from low to high.

Source

pub async fn wait_for_falling_edge(&mut self)

Wait for the pin to undergo a transition from high to low.

Source

pub async fn wait_for_any_edge(&mut self)

Wait for the pin to undergo any transition, i.e low to high OR high to low.

Source§

impl<'d, M: Mode> OutputOpenDrain<'d, M>

Source

pub fn set_pullup(&mut self, enable: bool)

Set the pin’s pull-up.

Source

pub fn set_drive_strength(&mut self, strength: Drive)

Set the pin’s drive strength.

Source

pub fn set_slew_rate(&mut self, slew_rate: SlewRate)

Set the pin’s slew rate.

Source

pub fn set_high(&mut self)

Set the output as high.

Source

pub fn set_low(&mut self)

Set the output as low.

Source

pub fn set_level(&mut self, level: Level)

Set the output level.

Source

pub fn is_set_high(&self) -> bool

Is the output level high?

Source

pub fn is_set_low(&self) -> bool

Is the output level low?

Source

pub fn output_level(&self) -> Level

What level output is set to

Source

pub fn toggle(&mut self)

Toggle pin output

Source

pub fn is_high(&self) -> bool

Get whether the pin input level is high.

Source

pub fn is_low(&self) -> bool

Get whether the pin input level is low.

Source

pub fn level(&self) -> Level

Returns current pin level

Source

pub fn set_pad_isolation(&mut self, isolate: bool)

Set the pin’s pad isolation

Source

pub fn persist(self)

Give up the pin, leaving it configured.

Dropping disconnects the pin, this doesn’t. The pin keeps its configuration after the borrow it came from ends.

Trait Implementations§

Source§

impl<'d, M: Debug + Mode> Debug for OutputOpenDrain<'d, M>

Source§

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter. Read more
Source§

impl<'d, M: Mode> ErrorType for OutputOpenDrain<'d, M>

Source§

type Error = !

Error type
Source§

impl<'d, M: Mode> Format for OutputOpenDrain<'d, M>
where Flex<'d, M>: Format,

Source§

fn format(&self, f: Formatter<'_>)

Writes the defmt representation of self to fmt.
Source§

impl<'d, M: Mode> InputPin for OutputOpenDrain<'d, M>

Source§

type Error = !

Error type
Source§

fn is_high(&self) -> Result<bool, Self::Error>

Is the input pin high?
Source§

fn is_low(&self) -> Result<bool, Self::Error>

Is the input pin low?
Source§

impl<'d, M: Mode> InputPin for OutputOpenDrain<'d, M>

Source§

fn is_high(&mut self) -> Result<bool, Self::Error>

Is the input pin high?
Source§

fn is_low(&mut self) -> Result<bool, Self::Error>

Is the input pin low?
Source§

impl<'d, M: Mode> OutputPin for OutputOpenDrain<'d, M>

Source§

type Error = !

Error type
Source§

fn set_high(&mut self) -> Result<(), Self::Error>

Drives the pin high Read more
Source§

fn set_low(&mut self) -> Result<(), Self::Error>

Drives the pin low Read more
Source§

fn set_state(&mut self, state: PinState) -> Result<(), Self::Error>

Drives the pin high or low depending on the provided value Read more
Source§

impl<'d, M: Mode> OutputPin for OutputOpenDrain<'d, M>

Source§

fn set_high(&mut self) -> Result<(), Self::Error>

Drives the pin high. Read more
Source§

fn set_low(&mut self) -> Result<(), Self::Error>

Drives the pin low. Read more
Source§

fn set_state(&mut self, state: PinState) -> Result<(), Self::Error>

Drives the pin high or low depending on the provided value. Read more
Source§

impl<'d, M: Mode> StatefulOutputPin for OutputOpenDrain<'d, M>

Source§

fn is_set_high(&self) -> Result<bool, Self::Error>

Is the pin in drive high mode? Read more
Source§

fn is_set_low(&self) -> Result<bool, Self::Error>

Is the pin in drive low mode? Read more
Source§

impl<'d, M: Mode> StatefulOutputPin for OutputOpenDrain<'d, M>

Source§

fn is_set_high(&mut self) -> Result<bool, Self::Error>

Is the pin in drive high mode? Read more
Source§

fn is_set_low(&mut self) -> Result<bool, Self::Error>

Is the pin in drive low mode? Read more
Source§

fn toggle(&mut self) -> Result<(), Self::Error>

Toggle pin output.
Source§

impl<'d, M: Mode> ToggleableOutputPin for OutputOpenDrain<'d, M>

Source§

type Error = !

Error type
Source§

fn toggle(&mut self) -> Result<(), Self::Error>

Toggle pin output.
Source§

impl<'d> Wait for OutputOpenDrain<'d, Async>

Source§

async fn wait_for_high(&mut self) -> Result<(), Self::Error>

Wait until the pin is high. If it is already high, return immediately. Read more
Source§

async fn wait_for_low(&mut self) -> Result<(), Self::Error>

Wait until the pin is low. If it is already low, return immediately. Read more
Source§

async fn wait_for_rising_edge(&mut self) -> Result<(), Self::Error>

Wait for the pin to undergo a transition from low to high. Read more
Source§

async fn wait_for_falling_edge(&mut self) -> Result<(), Self::Error>

Wait for the pin to undergo a transition from high to low. Read more
Source§

async fn wait_for_any_edge(&mut self) -> Result<(), Self::Error>

Wait for the pin to undergo any transition, i.e low to high OR high to low.

Auto Trait Implementations§

§

impl<'d, M = Blocking> !UnwindSafe for OutputOpenDrain<'d, M>

§

impl<'d, M> Forget for OutputOpenDrain<'d, M>

§

impl<'d, M> Freeze for OutputOpenDrain<'d, M>
where Flex<'d, M>: Freeze,

§

impl<'d, M> Move for OutputOpenDrain<'d, M>

§

impl<'d, M> RefUnwindSafe for OutputOpenDrain<'d, M>
where Flex<'d, M>: RefUnwindSafe,

§

impl<'d, M> Send for OutputOpenDrain<'d, M>
where Flex<'d, M>: Send,

§

impl<'d, M> Sync for OutputOpenDrain<'d, M>
where Flex<'d, M>: Sync,

§

impl<'d, M> Unpin for OutputOpenDrain<'d, M>
where Flex<'d, M>: Unpin,

§

impl<'d, M> UnsafeUnpin for OutputOpenDrain<'d, M>
where Flex<'d, M>: UnsafeUnpin,

Blanket Implementations§

Source§

impl<T> Any for T
where T: 'static + ?Sized,

Source§

fn type_id(&self) -> TypeId

Gets the TypeId of self. Read more
Source§

impl<T> Borrow<T> for T
where T: ?Sized,

Source§

fn borrow(&self) -> &T

Immutably borrows from an owned value. Read more
Source§

impl<T> BorrowMut<T> for T
where T: ?Sized,

Source§

fn borrow_mut(&mut self) -> &mut T

Mutably borrows from an owned value. Read more
Source§

impl<T> From<T> for T

Source§

fn from(t: T) -> T

Returns the argument unchanged.

Source§

impl<T, U> Into<U> for T
where U: From<T>,

Source§

fn into(self) -> U

Calls U::from(self).

That is, this conversion is whatever the implementation of From<T> for U chooses to do.

Source§

impl<T, U> TryFrom<U> for T
where U: Into<T>,

Source§

type Error = !

The type returned in the event of a conversion error.
Source§

fn try_from(value: U) -> Result<T, !>

Performs the conversion.
Source§

impl<T, U> TryInto<U> for T
where U: TryFrom<T>,

Source§

type Error = <U as TryFrom<T>>::Error

The type returned in the event of a conversion error.
Source§

fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>

Performs the conversion.