Struct stm32_metapac::syscfg::regs::Cfgr1

#[repr(transparent)]
pub struct Cfgr1(pub u32);

configuration register 1

Tuple Fields

0: u32

Implementations

impl Cfgr1

pub const fn mem_mode(&self) -> MemMode

Memory mapping selection bits. This bitfield controlled by software selects the memory internally mapped at the address 0x0000_0000. Its reset value is determined by the boot mode configuration. Refer to Reference Manual section 2.5 for more details.

pub fn set_mem_mode(&mut self, val: MemMode)

Memory mapping selection bits. This bitfield controlled by software selects the memory internally mapped at the address 0x0000_0000. Its reset value is determined by the boot mode configuration. Refer to Reference Manual section 2.5 for more details.

pub const fn pa11_rmp(&self) -> bool

PA11 pin remapping This bit is set and cleared by software. When set, it remaps the PA11 pin to operate as PA9 GPIO port, instead as PA11 GPIO port.

pub fn set_pa11_rmp(&mut self, val: bool)

PA11 pin remapping This bit is set and cleared by software. When set, it remaps the PA11 pin to operate as PA9 GPIO port, instead as PA11 GPIO port.

pub const fn pa12_rmp(&self) -> bool

PA12 pin remapping This bit is set and cleared by software. When set, it remaps the PA12 pin to operate as PA10 GPIO port, instead as PA12 GPIO port.

pub fn set_pa12_rmp(&mut self, val: bool)

PA12 pin remapping This bit is set and cleared by software. When set, it remaps the PA12 pin to operate as PA10 GPIO port, instead as PA12 GPIO port.

pub const fn ir_pol(&self) -> bool

IR output polarity selection

pub fn set_ir_pol(&mut self, val: bool)

IR output polarity selection

pub const fn ir_mod(&self) -> u8

IR Modulation Envelope signal selection.

pub fn set_ir_mod(&mut self, val: u8)

IR Modulation Envelope signal selection.

pub const fn boosten(&self) -> bool

I/O analog switch voltage booster enable

pub fn set_boosten(&mut self, val: bool)

I/O analog switch voltage booster enable

pub const fn ucpd1_strobe(&self) -> bool

Strobe signal bit for UCPD1

pub fn set_ucpd1_strobe(&mut self, val: bool)

Strobe signal bit for UCPD1

pub const fn ucpd2_strobe(&self) -> bool

Strobe signal bit for UCPD2

pub fn set_ucpd2_strobe(&mut self, val: bool)

Strobe signal bit for UCPD2

pub const fn i2c_pbx_fmp(&self) -> u8

Fast Mode Plus (FM+) driving capability activation bits

pub fn set_i2c_pbx_fmp(&mut self, val: u8)

Fast Mode Plus (FM+) driving capability activation bits

pub const fn i2c1_fmp(&self) -> bool

FM+ driving capability activation for I2C1

pub fn set_i2c1_fmp(&mut self, val: bool)

FM+ driving capability activation for I2C1

pub const fn i2c2_fmp(&self) -> bool

FM+ driving capability activation for I2C2

pub fn set_i2c2_fmp(&mut self, val: bool)

FM+ driving capability activation for I2C2

pub const fn i2c_pax_fmp(&self) -> u8

Fast Mode Plus (FM+) driving capability activation bits

pub fn set_i2c_pax_fmp(&mut self, val: u8)

Fast Mode Plus (FM+) driving capability activation bits

Trait Implementations

impl Clone for Cfgr1

fn clone(&self) -> Cfgr1

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Default for Cfgr1

fn default() -> Cfgr1

Returns the “default value” for a type.

impl PartialEq for Cfgr1

fn eq(&self, other: &Cfgr1) -> bool

Tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

Tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl Copy for Cfgr1

impl Eq for Cfgr1

impl StructuralPartialEq for Cfgr1