Struct stm32_metapac::i3c::regs::Cr

#[repr(transparent)]
pub struct Cr(pub u32);

I3C message control register.

Tuple Fields

0: u32

Implementations

impl Cr

pub const fn dcnt(&self) -> u16

count of data to transfer during a read or write message, in bytes (whatever I3C is acting as controller/target) Linear encoding up to 64 Kbytes -1 …

pub fn set_dcnt(&mut self, val: u16)

count of data to transfer during a read or write message, in bytes (whatever I3C is acting as controller/target) Linear encoding up to 64 Kbytes -1 …

pub const fn rnw(&self) -> Rnw

read / non-write message (when I3C is acting as controller) When I3C is acting as controller, this field is used if MTYPE[3:0]=0010 (private message) or MTYPE[3:0]=0011 (direct message) or MTYPE[3:0]=0100 (legacy I2C message), in order to emit the RnW bit on the I3C bus.

pub fn set_rnw(&mut self, val: Rnw)

read / non-write message (when I3C is acting as controller) When I3C is acting as controller, this field is used if MTYPE[3:0]=0010 (private message) or MTYPE[3:0]=0011 (direct message) or MTYPE[3:0]=0100 (legacy I2C message), in order to emit the RnW bit on the I3C bus.

pub const fn add(&self) -> u8

7-bit I3C dynamic / I2C static target address (when I3C is acting as controller) When I3C is acting as controller, this field is used if MTYPE[3:0]=0010 (private message) or MTYPE[3:0]=0011 (direct message) or MTYPE[3:0]=0100 (legacy I2C message).

pub fn set_add(&mut self, val: u8)

7-bit I3C dynamic / I2C static target address (when I3C is acting as controller) When I3C is acting as controller, this field is used if MTYPE[3:0]=0010 (private message) or MTYPE[3:0]=0011 (direct message) or MTYPE[3:0]=0100 (legacy I2C message).

pub const fn mtype(&self) -> u8

message type (whatever I3C is acting as controller/target) Bits[26:0] are ignored. After M2 error detection on an I3C SDR message, this is needed for SCL “stuck at” recovery. Bits[26:0] are ignored. If I3C_CFGR.EXITPTRN=1, an HDR exit pattern is emitted on the bus to generate an escalation fault. Bits[23:17] (ADD[6:0]) is the emitted 7-bit dynamic address. Bit[16] (RNW) is the emitted RnW bit. The transferred private message is: {S / S+7’h7E+RnW=0+Sr / Sr+} + 7-bit DynAddr + RnW + (8-bit Data + T) + Sr/P. After a S (START), depending on I3C_CFGR.NOARBH, the arbitrable header (7’h7E+RnW=0) is inserted or not. Sr+: after a Sr (Repeated Start), the hardware automatically inserts (7’h7E+RnW=0) if needed, i.e. if it follows an I3C direct message without ending by a P (Stop). Bits[23:17] (ADD[6:0]) is the emitted 7-bit dynamic address. Bit[16] (RNW) is the emitted RnW bit. The transferred direct message is: Sr + 7-bit DynAddr + RnW + (8-bit Data + T) + Sr/P Bits[23:17] (ADD[6:0]) is the emitted 7-bit static address. Bit[16] (RNW) is the emitted RnW bit. The transferred legacy I2C message is: {S / S+ 7’h7E+RnW=0 + Sr / Sr+} + 7-bit StaAddr + RnW + (8-bit Data + T) + Sr/P. After a S (START), depending on I3C_CFGR.NOARBH, the arbitrable header (7’h7E+RnW=0) is inserted or not. Sr+*: after a Sr (Repeated Start), the hardware automatically inserts (7’h7E+RnW=0) if needed, i.e. if it follows an I3C direct message without ending by a P (Stop). 1xxx: reserved (when I3C is acting as I3C controller, used when target) 0xxx: reserved {S +} 7’h02 addr + RnW=0 {S +} 7-bit I3C_DEVR0.DA[6:0]

• RnW=0 after a bus available condition (the target first emits a START request), or once the controller drives a START. {S +} 7-bit I3C_DEVR0.DA[6:0]
• RnW=1 (+Ack/Nack from controller) When acknowledged from controller, the next (optional, depending on I3C_BCR.BCR2) transmitted IBI payload data is defined by I3C_CR.DCNT[15:0] and must be consistently programmed vs the maximum IBI payload data size which is defined by I3C_IBIDR.IBIP[2:0]. Others: reserved.

pub fn set_mtype(&mut self, val: u8)

message type (whatever I3C is acting as controller/target) Bits[26:0] are ignored. After M2 error detection on an I3C SDR message, this is needed for SCL “stuck at” recovery. Bits[26:0] are ignored. If I3C_CFGR.EXITPTRN=1, an HDR exit pattern is emitted on the bus to generate an escalation fault. Bits[23:17] (ADD[6:0]) is the emitted 7-bit dynamic address. Bit[16] (RNW) is the emitted RnW bit. The transferred private message is: {S / S+7’h7E+RnW=0+Sr / Sr+} + 7-bit DynAddr + RnW + (8-bit Data + T) + Sr/P. After a S (START), depending on I3C_CFGR.NOARBH, the arbitrable header (7’h7E+RnW=0) is inserted or not. Sr+: after a Sr (Repeated Start), the hardware automatically inserts (7’h7E+RnW=0) if needed, i.e. if it follows an I3C direct message without ending by a P (Stop). Bits[23:17] (ADD[6:0]) is the emitted 7-bit dynamic address. Bit[16] (RNW) is the emitted RnW bit. The transferred direct message is: Sr + 7-bit DynAddr + RnW + (8-bit Data + T) + Sr/P Bits[23:17] (ADD[6:0]) is the emitted 7-bit static address. Bit[16] (RNW) is the emitted RnW bit. The transferred legacy I2C message is: {S / S+ 7’h7E+RnW=0 + Sr / Sr+} + 7-bit StaAddr + RnW + (8-bit Data + T) + Sr/P. After a S (START), depending on I3C_CFGR.NOARBH, the arbitrable header (7’h7E+RnW=0) is inserted or not. Sr+*: after a Sr (Repeated Start), the hardware automatically inserts (7’h7E+RnW=0) if needed, i.e. if it follows an I3C direct message without ending by a P (Stop). 1xxx: reserved (when I3C is acting as I3C controller, used when target) 0xxx: reserved {S +} 7’h02 addr + RnW=0 {S +} 7-bit I3C_DEVR0.DA[6:0]

• RnW=0 after a bus available condition (the target first emits a START request), or once the controller drives a START. {S +} 7-bit I3C_DEVR0.DA[6:0]
• RnW=1 (+Ack/Nack from controller) When acknowledged from controller, the next (optional, depending on I3C_BCR.BCR2) transmitted IBI payload data is defined by I3C_CR.DCNT[15:0] and must be consistently programmed vs the maximum IBI payload data size which is defined by I3C_IBIDR.IBIP[2:0]. Others: reserved.

pub const fn mend(&self) -> Mend

message end type (when the I3C is acting as controller).

pub fn set_mend(&mut self, val: Mend)

message end type (when the I3C is acting as controller).

Trait Implementations

impl Clone for Cr

fn clone(&self) -> Cr

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Default for Cr

fn default() -> Cr

Returns the “default value” for a type.

impl PartialEq for Cr

fn eq(&self, other: &Cr) -> bool

Tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

Tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl Copy for Cr

impl Eq for Cr

impl StructuralPartialEq for Cr