Struct stm32_metapac::adccommon::regs::Ccr

#[repr(transparent)]
pub struct Ccr(pub u32);

Expand description

common control register

Tuple Fields§

§0: u32

Implementations§

§

impl Ccr

pub const fn dual(&self) -> Dual

Dual ADC mode selection These bits are written by software to select the operating mode. 0 value means Independent Mode. Values 00001 to 01001 means Dual mode, master and slave ADCs are working together. All other combinations are reserved and must not be programmed Note: The software is allowed to write these bits only when the ADCs are disabled (ADCAL = 0, JADSTART = 0, ADSTART = 0, ADSTP = 0, ADDIS = 0 and ADEN = 0).

pub fn set_dual(&mut self, val: Dual)

Dual ADC mode selection These bits are written by software to select the operating mode. 0 value means Independent Mode. Values 00001 to 01001 means Dual mode, master and slave ADCs are working together. All other combinations are reserved and must not be programmed Note: The software is allowed to write these bits only when the ADCs are disabled (ADCAL = 0, JADSTART = 0, ADSTART = 0, ADSTP = 0, ADDIS = 0 and ADEN = 0).

pub const fn delay(&self) -> u8

Delay between 2 sampling phases These bits are set and cleared by software. These bits are used in dual interleaved modes. Refer to for the value of ADC resolution versus DELAY bits values. Note: The software is allowed to write these bits only when the ADCs are disabled (ADCAL = 0, JADSTART = 0, ADSTART = 0, ADSTP = 0, ADDIS = 0 and ADEN = 0).

pub fn set_delay(&mut self, val: u8)

Delay between 2 sampling phases These bits are set and cleared by software. These bits are used in dual interleaved modes. Refer to for the value of ADC resolution versus DELAY bits values. Note: The software is allowed to write these bits only when the ADCs are disabled (ADCAL = 0, JADSTART = 0, ADSTART = 0, ADSTP = 0, ADDIS = 0 and ADEN = 0).

pub const fn dmacfg(&self) -> Dmacfg

DMA configuration (for dual ADC mode) This bit is set and cleared by software to select between two DMA modes of operation and is effective only when DMAEN = 1. For more details, refer to Note: The software is allowed to write these bits only when ADSTART = 0 (which ensures that no regular conversion is ongoing).

pub fn set_dmacfg(&mut self, val: Dmacfg)

DMA configuration (for dual ADC mode) This bit is set and cleared by software to select between two DMA modes of operation and is effective only when DMAEN = 1. For more details, refer to Note: The software is allowed to write these bits only when ADSTART = 0 (which ensures that no regular conversion is ongoing).

pub const fn mdma(&self) -> Mdma

Direct memory access mode for dual ADC mode This bitfield is set and cleared by software. Refer to the DMA controller section for more details. Note: The software is allowed to write these bits only when ADSTART = 0 (which ensures that no regular conversion is ongoing).

pub fn set_mdma(&mut self, val: Mdma)

Direct memory access mode for dual ADC mode This bitfield is set and cleared by software. Refer to the DMA controller section for more details. Note: The software is allowed to write these bits only when ADSTART = 0 (which ensures that no regular conversion is ongoing).

pub const fn ckmode(&self) -> Ckmode

ADC clock mode These bits are set and cleared by software to define the ADC clock scheme (which is common to both master and slave ADCs): In all synchronous clock modes, there is no jitter in the delay from a timer trigger to the start of a conversion. Note: The software is allowed to write these bits only when the ADCs are disabled (ADCAL = 0, JADSTART = 0, ADSTART = 0, ADSTP = 0, ADDIS = 0 and ADEN = 0).

pub fn set_ckmode(&mut self, val: Ckmode)

ADC clock mode These bits are set and cleared by software to define the ADC clock scheme (which is common to both master and slave ADCs): In all synchronous clock modes, there is no jitter in the delay from a timer trigger to the start of a conversion. Note: The software is allowed to write these bits only when the ADCs are disabled (ADCAL = 0, JADSTART = 0, ADSTART = 0, ADSTP = 0, ADDIS = 0 and ADEN = 0).

pub const fn presc(&self) -> Presc

ADC prescaler These bits are set and cleared by software to select the frequency of the clock to the ADC. The clock is common for all the ADCs. other: reserved Note: The software is allowed to write these bits only when the ADC is disabled (ADCAL = 0, JADSTART = 0, ADSTART = 0, ADSTP = 0, ADDIS = 0 and ADEN = 0). The ADC prescaler value is applied only when CKMODE[1:0] = 0b00.

pub fn set_presc(&mut self, val: Presc)

ADC prescaler These bits are set and cleared by software to select the frequency of the clock to the ADC. The clock is common for all the ADCs. other: reserved Note: The software is allowed to write these bits only when the ADC is disabled (ADCAL = 0, JADSTART = 0, ADSTART = 0, ADSTP = 0, ADDIS = 0 and ADEN = 0). The ADC prescaler value is applied only when CKMODE[1:0] = 0b00.