Struct stm32_metapac::i3c::regs::Devr0

#[repr(transparent)]
pub struct Devr0(pub u32);

Expand description

I3C own device characteristics register.

Tuple Fields§

§0: u32

Implementations§

§

impl Devr0

pub const fn daval(&self) -> bool

dynamic address is valid (when the I3C is acting as target) When the I3C is acting as controller, this field can be written by software, for validating its own dynamic address, for example before a controller-role hand-off. When the I3C is acting as target, this field is asserted by hardware on the acknowledge of the broadcast ENTDAA CCC or the direct SETNEWDA CCC, and this field is cleared by hardware on the acknowledge of the broadcast RSTDAA CCC.

pub fn set_daval(&mut self, val: bool)

dynamic address is valid (when the I3C is acting as target) When the I3C is acting as controller, this field can be written by software, for validating its own dynamic address, for example before a controller-role hand-off. When the I3C is acting as target, this field is asserted by hardware on the acknowledge of the broadcast ENTDAA CCC or the direct SETNEWDA CCC, and this field is cleared by hardware on the acknowledge of the broadcast RSTDAA CCC.

pub const fn da(&self) -> u8

7-bit dynamic address When the I3C is acting as controller, this field can be written by software, for defining its own dynamic address. When the I3C is acting as target, this field is updated by hardware on the reception of either the broadcast ENTDAA CCC or the direct SETNEWDA CCC.

pub fn set_da(&mut self, val: u8)

7-bit dynamic address When the I3C is acting as controller, this field can be written by software, for defining its own dynamic address. When the I3C is acting as target, this field is updated by hardware on the reception of either the broadcast ENTDAA CCC or the direct SETNEWDA CCC.

pub const fn ibien(&self) -> bool

IBI request enable (when the I3C is acting as target) This field is initially written by software when I3C_CFGR.EN=0, and is updated by hardware on the reception of DISEC CCC with DISINT=1 (i.e. cleared) and the reception of ENEC CCC with ENINT=1 (i.e. set).

pub fn set_ibien(&mut self, val: bool)

IBI request enable (when the I3C is acting as target) This field is initially written by software when I3C_CFGR.EN=0, and is updated by hardware on the reception of DISEC CCC with DISINT=1 (i.e. cleared) and the reception of ENEC CCC with ENINT=1 (i.e. set).

pub const fn cren(&self) -> bool

controller-role request enable (when the I3C is acting as target) This field is initially written by software when I3C_CFGR.EN=0, and is updated by hardware on the reception of DISEC CCC with DISCR=1 (i.e. cleared) and the reception of ENEC CCC with ENCR=1 (i.e. set).

pub fn set_cren(&mut self, val: bool)

controller-role request enable (when the I3C is acting as target) This field is initially written by software when I3C_CFGR.EN=0, and is updated by hardware on the reception of DISEC CCC with DISCR=1 (i.e. cleared) and the reception of ENEC CCC with ENCR=1 (i.e. set).

pub const fn hjen(&self) -> bool

hot-join request enable (when the I3C is acting as target) This field is initially written by software when I3C_CFGR.EN=0, and is updated by hardware on the reception of DISEC CCC with DISHJ=1 (i.e. cleared) and the reception of ENEC CCC with ENHJ=1 (i.e. set).

pub fn set_hjen(&mut self, val: bool)

hot-join request enable (when the I3C is acting as target) This field is initially written by software when I3C_CFGR.EN=0, and is updated by hardware on the reception of DISEC CCC with DISHJ=1 (i.e. cleared) and the reception of ENEC CCC with ENHJ=1 (i.e. set).

pub const fn as_(&self) -> u8

activity state (when the I3C is acting as target) This read field is updated by hardware on the reception of a ENTASx CCC (enter activity state, with x=0-3):.

pub fn set_as_(&mut self, val: u8)

activity state (when the I3C is acting as target) This read field is updated by hardware on the reception of a ENTASx CCC (enter activity state, with x=0-3):.

pub const fn rstact(&self) -> Rstact

reset action/level on received reset pattern (when the I3C is acting as target) This read field is used by hardware on the reception of a direct read RSTACT CCC in order to return the corresponding data byte on the I3C bus. This read field is updated by hardware on the reception of a broadcast or direct write RSTACT CCC (target reset action). Only the defining bytes 0x00, 0x01 and 0x02 are mapped, and RSTACT[1:0] = Defining Byte[1:0]. a) partially reset the I3C peripheral, by a write and clear of the enable bit of the i3C configuration register (i.e. write I3C_CFGR.EN=0). This reset the I3C bus interface and the I3C kernel sub-parts, without modifying the content of the I3C APB registers (excepted the I3C_CFGR.EN bit). b) reset fully the I3C peripheral including all its registers via a write and set to the I3C reset control bit of the RCC (Reset and Clock Controller) register. a system reset. This has the same impact as a pin reset (i.e. NRST=0) (refer to RCC functional description - Reset part): – the software writes and set the AICR.SYSRESETREQ register control bit, when the device is controlled by a CortexTM-M. – the software writes and set the RCC_GRSTCSETR.SYSRST=1, when the device is controlled by a CortexTM-A.

pub fn set_rstact(&mut self, val: Rstact)

reset action/level on received reset pattern (when the I3C is acting as target) This read field is used by hardware on the reception of a direct read RSTACT CCC in order to return the corresponding data byte on the I3C bus. This read field is updated by hardware on the reception of a broadcast or direct write RSTACT CCC (target reset action). Only the defining bytes 0x00, 0x01 and 0x02 are mapped, and RSTACT[1:0] = Defining Byte[1:0]. a) partially reset the I3C peripheral, by a write and clear of the enable bit of the i3C configuration register (i.e. write I3C_CFGR.EN=0). This reset the I3C bus interface and the I3C kernel sub-parts, without modifying the content of the I3C APB registers (excepted the I3C_CFGR.EN bit). b) reset fully the I3C peripheral including all its registers via a write and set to the I3C reset control bit of the RCC (Reset and Clock Controller) register. a system reset. This has the same impact as a pin reset (i.e. NRST=0) (refer to RCC functional description - Reset part): – the software writes and set the AICR.SYSRESETREQ register control bit, when the device is controlled by a CortexTM-M. – the software writes and set the RCC_GRSTCSETR.SYSRST=1, when the device is controlled by a CortexTM-A.

pub const fn rstval(&self) -> bool

reset action is valid (when the I3C is acting as target) This read bit is asserted by hardware to indicate that the RTSACT[1:0] field has been updated on the reception of a broadcast or direct write RSTACT CCC (target reset action) and is valid. This field is cleared by hardware when the target receives a frame start. If RSTVAL=1: when the RSTF is asserted (and/or the corresponding interrupt if enabled), I3C_DEVR0.RSTACT[1:0] dictates the reset action to be performed by the software if any. If RSTVAL=0: when the RSTF is asserted (and/or the corresponding interrupt if enabled), the software should issue an I3C reset after a first detected reset pattern, and a system reset on the second one.

pub fn set_rstval(&mut self, val: bool)

reset action is valid (when the I3C is acting as target) This read bit is asserted by hardware to indicate that the RTSACT[1:0] field has been updated on the reception of a broadcast or direct write RSTACT CCC (target reset action) and is valid. This field is cleared by hardware when the target receives a frame start. If RSTVAL=1: when the RSTF is asserted (and/or the corresponding interrupt if enabled), I3C_DEVR0.RSTACT[1:0] dictates the reset action to be performed by the software if any. If RSTVAL=0: when the RSTF is asserted (and/or the corresponding interrupt if enabled), the software should issue an I3C reset after a first detected reset pattern, and a system reset on the second one.