stm32-metapac

Crates

git

Versions

stm32h755zi-cm4

Flavors

Struct stm32_metapac::cec::regs::Cfgr

#[repr(transparent)]
pub struct Cfgr(pub u32);
Expand description

This register is used to configure the HDMI-CEC controller. It is mandatory to write CEC_CFGR only when CECEN=0.

Tuple Fields§

§0: u32

Implementations§

§

impl Cfgr

pub const fn sft(&self) -> u8

Signal Free Time SFT bits are set by software. In the SFT=0x0 configuration the number of nominal data bit periods waited before transmission is ruled by hardware according to the transmission history. In all the other configurations the SFT number is determined by software. * 0x0 ** 2.5 Data-Bit periods if CEC is the last bus initiator with unsuccessful transmission (ARBLST=1, TXERR=1, TXUDR=1 or TXACKE= 1) ** 4 Data-Bit periods if CEC is the new bus initiator ** 6 Data-Bit periods if CEC is the last bus initiator with successful transmission (TXEOM=1) * 0x1: 0.5 nominal data bit periods * 0x2: 1.5 nominal data bit periods * 0x3: 2.5 nominal data bit periods * 0x4: 3.5 nominal data bit periods * 0x5: 4.5 nominal data bit periods * 0x6: 5.5 nominal data bit periods * 0x7: 6.5 nominal data bit periods.

pub fn set_sft(&mut self, val: u8)

Signal Free Time SFT bits are set by software. In the SFT=0x0 configuration the number of nominal data bit periods waited before transmission is ruled by hardware according to the transmission history. In all the other configurations the SFT number is determined by software. * 0x0 ** 2.5 Data-Bit periods if CEC is the last bus initiator with unsuccessful transmission (ARBLST=1, TXERR=1, TXUDR=1 or TXACKE= 1) ** 4 Data-Bit periods if CEC is the new bus initiator ** 6 Data-Bit periods if CEC is the last bus initiator with successful transmission (TXEOM=1) * 0x1: 0.5 nominal data bit periods * 0x2: 1.5 nominal data bit periods * 0x3: 2.5 nominal data bit periods * 0x4: 3.5 nominal data bit periods * 0x5: 4.5 nominal data bit periods * 0x6: 5.5 nominal data bit periods * 0x7: 6.5 nominal data bit periods.

pub const fn rxtol(&self) -> bool

Rx-Tolerance The RXTOL bit is set and cleared by software. ** Start-Bit, +/- 200 s rise, +/- 200 s fall. ** Data-Bit: +/- 200 s rise. +/- 350 s fall. ** Start-Bit: +/- 400 s rise, +/- 400 s fall ** Data-Bit: +/-300 s rise, +/- 500 s fall.

pub fn set_rxtol(&mut self, val: bool)

Rx-Tolerance The RXTOL bit is set and cleared by software. ** Start-Bit, +/- 200 s rise, +/- 200 s fall. ** Data-Bit: +/- 200 s rise. +/- 350 s fall. ** Start-Bit: +/- 400 s rise, +/- 400 s fall ** Data-Bit: +/-300 s rise, +/- 500 s fall.

pub const fn brestp(&self) -> bool

Rx-Stop on Bit Rising Error The BRESTP bit is set and cleared by software.

pub fn set_brestp(&mut self, val: bool)

Rx-Stop on Bit Rising Error The BRESTP bit is set and cleared by software.

pub const fn bregen(&self) -> bool

Generate Error-Bit on Bit Rising Error The BREGEN bit is set and cleared by software. Note: If BRDNOGEN=0, an Error-bit is generated upon BRE detection with BRESTP=1 in broadcast even if BREGEN=0.

pub fn set_bregen(&mut self, val: bool)

Generate Error-Bit on Bit Rising Error The BREGEN bit is set and cleared by software. Note: If BRDNOGEN=0, an Error-bit is generated upon BRE detection with BRESTP=1 in broadcast even if BREGEN=0.

pub const fn lbpegen(&self) -> bool

Generate Error-Bit on Long Bit Period Error The LBPEGEN bit is set and cleared by software. Note: If BRDNOGEN=0, an Error-bit is generated upon LBPE detection in broadcast even if LBPEGEN=0.

pub fn set_lbpegen(&mut self, val: bool)

Generate Error-Bit on Long Bit Period Error The LBPEGEN bit is set and cleared by software. Note: If BRDNOGEN=0, an Error-bit is generated upon LBPE detection in broadcast even if LBPEGEN=0.

pub const fn brdnogen(&self) -> bool

Avoid Error-Bit Generation in Broadcast The BRDNOGEN bit is set and cleared by software.

pub fn set_brdnogen(&mut self, val: bool)

Avoid Error-Bit Generation in Broadcast The BRDNOGEN bit is set and cleared by software.

pub const fn sftopt(&self) -> bool

SFT Option Bit The SFTOPT bit is set and cleared by software.

pub fn set_sftopt(&mut self, val: bool)

SFT Option Bit The SFTOPT bit is set and cleared by software.

pub const fn oar(&self) -> u16

Own addresses configuration The OAR bits are set by software to select which destination logical addresses has to be considered in receive mode. Each bit, when set, enables the CEC logical address identified by the given bit position. At the end of HEADER reception, the received destination address is compared with the enabled addresses. In case of matching address, the incoming message is acknowledged and received. In case of non-matching address, the incoming message is received only in listen mode (LSTN=1), but without acknowledge sent. Broadcast messages are always received. Example: OAR = 0b000 0000 0010 0001 means that CEC acknowledges addresses 0x0 and 0x5. Consequently, each message directed to one of these addresses is received.

pub fn set_oar(&mut self, val: u16)

Own addresses configuration The OAR bits are set by software to select which destination logical addresses has to be considered in receive mode. Each bit, when set, enables the CEC logical address identified by the given bit position. At the end of HEADER reception, the received destination address is compared with the enabled addresses. In case of matching address, the incoming message is acknowledged and received. In case of non-matching address, the incoming message is received only in listen mode (LSTN=1), but without acknowledge sent. Broadcast messages are always received. Example: OAR = 0b000 0000 0010 0001 means that CEC acknowledges addresses 0x0 and 0x5. Consequently, each message directed to one of these addresses is received.

pub const fn lstn(&self) -> bool

Listen mode LSTN bit is set and cleared by software.

pub fn set_lstn(&mut self, val: bool)

Listen mode LSTN bit is set and cleared by software.

Trait Implementations§

§

impl Clone for Cfgr

§

fn clone(&self) -> Cfgr

Returns a copy of the value. Read more
1.0.0 · source§

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source. Read more
§

impl Default for Cfgr

§

fn default() -> Cfgr

Returns the “default value” for a type. Read more
§

impl PartialEq for Cfgr

§

fn eq(&self, other: &Cfgr) -> bool

Tests for self and other values to be equal, and is used by ==.
1.0.0 · source§

fn ne(&self, other: &Rhs) -> bool

Tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.
§

impl Copy for Cfgr

§

impl Eq for Cfgr

§

impl StructuralPartialEq for Cfgr

Auto Trait Implementations§

§

impl Freeze for Cfgr

§

impl RefUnwindSafe for Cfgr

§

impl Send for Cfgr

§

impl Sync for Cfgr

§

impl Unpin for Cfgr

§

impl UnwindSafe for Cfgr

Blanket Implementations§

source§

impl<T> Any for T
where T: 'static + ?Sized,

source§

fn type_id(&self) -> TypeId

Gets the TypeId of self. Read more
source§

impl<T> Borrow<T> for T
where T: ?Sized,

source§

fn borrow(&self) -> &T

Immutably borrows from an owned value. Read more
source§

impl<T> BorrowMut<T> for T
where T: ?Sized,

source§

fn borrow_mut(&mut self) -> &mut T

Mutably borrows from an owned value. Read more
source§

impl<T> CloneToUninit for T
where T: Clone,

source§

unsafe fn clone_to_uninit(&self, dst: *mut T)

🔬This is a nightly-only experimental API. (clone_to_uninit)
Performs copy-assignment from self to dst. Read more
source§

impl<T> From<T> for T

source§

fn from(t: T) -> T

Returns the argument unchanged.

source§

impl<T, U> Into<U> for T
where U: From<T>,

source§

fn into(self) -> U

Calls U::from(self).

That is, this conversion is whatever the implementation of From<T> for U chooses to do.

source§

impl<T, U> TryFrom<U> for T
where U: Into<T>,

source§

type Error = Infallible

The type returned in the event of a conversion error.
source§

fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>

Performs the conversion.
source§

impl<T, U> TryInto<U> for T
where U: TryFrom<T>,

source§

type Error = <U as TryFrom<T>>::Error

The type returned in the event of a conversion error.
source§

fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>

Performs the conversion.