Struct stm32_metapac::flash::regs::Sr

#[repr(transparent)]
pub struct Sr(pub u32);

FLASH status register.

Tuple Fields

0: u32

Implementations

impl Sr

pub const fn busy(&self) -> bool

Busy flag This bit is set when an effective write, erase or option byte change operation is ongoing. It is possible to know what type of operation is being executed reading the flags IS_PROGRAM, IS_ERASE and IS_OPTCHANGE. BUSY cannot be cleared by application. It is automatically reset by hardware every time a step in a write, erase or option byte change operation completes. It is not recommended to do software polling on BUSY to know when one operation completed because, depending of operation, more pulses are possible for one only operation. For software polling it is therefore better to use QW flag or to check the EOPF flag.

pub fn set_busy(&mut self, val: bool)

Busy flag This bit is set when an effective write, erase or option byte change operation is ongoing. It is possible to know what type of operation is being executed reading the flags IS_PROGRAM, IS_ERASE and IS_OPTCHANGE. BUSY cannot be cleared by application. It is automatically reset by hardware every time a step in a write, erase or option byte change operation completes. It is not recommended to do software polling on BUSY to know when one operation completed because, depending of operation, more pulses are possible for one only operation. For software polling it is therefore better to use QW flag or to check the EOPF flag.

pub const fn wbne(&self) -> bool

Write buffer not empty flag This bit is set when the embedded Flash memory is waiting for new data to complete the write buffer. In this state, the write buffer is not empty. WBNE is reset by hardware each time the write buffer is complete or the write buffer is emptied following one of the event below: the application software forces the write operation using FW bit in FLASH_CR the embedded Flash memory detects an error that involves data loss the application software has disabled write operations This bit cannot be forced to 0. To reset it, clear the write buffer by performing any of the above listed actions, or send the missing data.

pub fn set_wbne(&mut self, val: bool)

Write buffer not empty flag This bit is set when the embedded Flash memory is waiting for new data to complete the write buffer. In this state, the write buffer is not empty. WBNE is reset by hardware each time the write buffer is complete or the write buffer is emptied following one of the event below: the application software forces the write operation using FW bit in FLASH_CR the embedded Flash memory detects an error that involves data loss the application software has disabled write operations This bit cannot be forced to 0. To reset it, clear the write buffer by performing any of the above listed actions, or send the missing data.

pub const fn qw(&self) -> bool

Wait queue flag This bit is set when a write, erase or option byte change operation is pending in the command queue buffer. It is not possible to know what type of programming operation is present in the queue. This flag is reset by hardware when all write, erase or option byte change operations have been executed and thus removed from the waiting queue(s). This bit cannot be forced to 0. It is reset after a deterministic time if no other operations are requested.

pub fn set_qw(&mut self, val: bool)

Wait queue flag This bit is set when a write, erase or option byte change operation is pending in the command queue buffer. It is not possible to know what type of programming operation is present in the queue. This flag is reset by hardware when all write, erase or option byte change operations have been executed and thus removed from the waiting queue(s). This bit cannot be forced to 0. It is reset after a deterministic time if no other operations are requested.

pub const fn crc_busy(&self) -> bool

CRC busy flag This bit is set when a CRC calculation is ongoing. This bit cannot be forced to 0. The user must wait until the CRC calculation has completed or disable CRC computation using CRC_EN bit in FLASH_CR register.

pub fn set_crc_busy(&mut self, val: bool)

CRC busy flag This bit is set when a CRC calculation is ongoing. This bit cannot be forced to 0. The user must wait until the CRC calculation has completed or disable CRC computation using CRC_EN bit in FLASH_CR register.

pub const fn is_program(&self) -> bool

Is a program This bit is set together with BUSY when a program operation is ongoing. It is cleared when BUSY is cleared. This flag can also raise with IS_OPTCHANGE, because an program operation can happen during an option change.

pub fn set_is_program(&mut self, val: bool)

Is a program This bit is set together with BUSY when a program operation is ongoing. It is cleared when BUSY is cleared. This flag can also raise with IS_OPTCHANGE, because an program operation can happen during an option change.

pub const fn is_erase(&self) -> bool

Is an erase This bit is set together with BUSY when an erase operation is ongoing. It is cleared when BUSY is cleared. This flag can also raise with IS_OPTCHANGE, because an erase operation can happen during an option change.

pub fn set_is_erase(&mut self, val: bool)

Is an erase This bit is set together with BUSY when an erase operation is ongoing. It is cleared when BUSY is cleared. This flag can also raise with IS_OPTCHANGE, because an erase operation can happen during an option change.

pub const fn is_optchange(&self) -> bool

Is an option change This bit is set together with BUSY when an option change operation is ongoing. It is cleared when BUSY is cleared. This flag can also raise with IS_PROGRAM or IS_ERASE, because a program or erase step is ongoing during option change.

pub fn set_is_optchange(&mut self, val: bool)

Is an option change This bit is set together with BUSY when an option change operation is ongoing. It is cleared when BUSY is cleared. This flag can also raise with IS_PROGRAM or IS_ERASE, because a program or erase step is ongoing during option change.

pub const fn rcheckf(&self) -> bool

Root code check flag This bit returns the status of the root code check performed following the first access to the Flash. This bit is cleared with RCHECKF bit in FLASH_FCR (optional).

pub fn set_rcheckf(&mut self, val: bool)

Root code check flag This bit returns the status of the root code check performed following the first access to the Flash. This bit is cleared with RCHECKF bit in FLASH_FCR (optional).

Trait Implementations

impl Clone for Sr

fn clone(&self) -> Sr

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Default for Sr

fn default() -> Sr

Returns the “default value” for a type.

impl PartialEq for Sr

fn eq(&self, other: &Sr) -> bool

Tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

Tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl Copy for Sr

impl Eq for Sr

impl StructuralPartialEq for Sr