Struct stm32_metapac::opamp::regs::Csr

#[repr(transparent)]
pub struct Csr(pub u32);

OPAMP control/status register.

Tuple Fields

0: u32

Implementations

impl Csr

pub const fn opampen(&self) -> bool

Operational amplifier Enable.

pub fn set_opampen(&mut self, val: bool)

Operational amplifier Enable.

pub const fn opalpm(&self) -> Opalpm

Operational amplifier Low Power Mode. The operational amplifier must be disable to change this configuration.

pub fn set_opalpm(&mut self, val: Opalpm)

Operational amplifier Low Power Mode. The operational amplifier must be disable to change this configuration.

pub const fn opamode(&self) -> Opamode

Operational amplifier PGA mode.

pub fn set_opamode(&mut self, val: Opamode)

Operational amplifier PGA mode.

pub const fn pga_gain(&self) -> PgaGain

Operational amplifier Programmable amplifier gain value.

pub fn set_pga_gain(&mut self, val: PgaGain)

Operational amplifier Programmable amplifier gain value.

pub const fn vm_sel(&self) -> VmSel

Inverting input selection. These bits are used only when OPAMODE = 00, 01 or 10. 1x: Inverting input not externally connected. These configurations are valid only when OPAMODE = 10 (PGA mode).

pub fn set_vm_sel(&mut self, val: VmSel)

Inverting input selection. These bits are used only when OPAMODE = 00, 01 or 10. 1x: Inverting input not externally connected. These configurations are valid only when OPAMODE = 10 (PGA mode).

pub const fn vp_sel(&self) -> VpSel

Non inverted input selection.

pub fn set_vp_sel(&mut self, val: VpSel)

Non inverted input selection.

pub const fn calon(&self) -> Calon

Calibration mode enabled.

pub fn set_calon(&mut self, val: Calon)

Calibration mode enabled.

pub const fn calsel(&self) -> Calsel

Calibration selection.

pub fn set_calsel(&mut self, val: Calsel)

Calibration selection.

pub const fn usertrim(&self) -> Usertrim

allows to switch from factory AOP offset trimmed values to AOP offset user trimmed values This bit is active for both mode normal and low-power.

pub fn set_usertrim(&mut self, val: Usertrim)

allows to switch from factory AOP offset trimmed values to AOP offset user trimmed values This bit is active for both mode normal and low-power.

pub const fn calout(&self) -> bool

Operational amplifier calibration output During calibration mode offset is trimmed when this signal toggle.

pub fn set_calout(&mut self, val: bool)

Operational amplifier calibration output During calibration mode offset is trimmed when this signal toggle.

pub const fn opa_range(&self) -> OpaRange

Operational amplifier power supply range for stability All AOP must be in power down to allow AOP-RANGE bit write. It applies to all AOP embedded in the product.

pub fn set_opa_range(&mut self, val: OpaRange)

Operational amplifier power supply range for stability All AOP must be in power down to allow AOP-RANGE bit write. It applies to all AOP embedded in the product.

Trait Implementations

impl Clone for Csr

fn clone(&self) -> Csr

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Default for Csr

fn default() -> Csr

Returns the “default value” for a type.

impl PartialEq for Csr

fn eq(&self, other: &Csr) -> bool

Tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

Tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl Copy for Csr

impl Eq for Csr

impl StructuralPartialEq for Csr