stm32-metapac

Crates

git

Versions

stm32u073k8

Flavors

Struct stm32_metapac::pwr::regs::Cr3

#[repr(transparent)]
pub struct Cr3(pub u32);
Expand description

Power control register 3

Tuple Fields§

§0: u32

Implementations§

§

impl Cr3

pub const fn ewup1(&self) -> bool

Enable Wake-up pin WKUP1 When this bit is set, the external wake-up pin WKUP1 is enabled and triggers a wake-up from Standby or Shutdown event when a rising or a falling edge occurs. The active edge is configured via the WP1 bit in the PWR_CR4 register.

pub fn set_ewup1(&mut self, val: bool)

Enable Wake-up pin WKUP1 When this bit is set, the external wake-up pin WKUP1 is enabled and triggers a wake-up from Standby or Shutdown event when a rising or a falling edge occurs. The active edge is configured via the WP1 bit in the PWR_CR4 register.

pub const fn ewup2(&self) -> bool

Enable Wake-up pin WKUP2 When this bit is set, the external wake-up pin WKUP2 is enabled and triggers a wake-up from Standby or Shutdown event when a rising or a falling edge occurs. The active edge is configured via the WP2 bit in the PWR_CR4 register.

pub fn set_ewup2(&mut self, val: bool)

Enable Wake-up pin WKUP2 When this bit is set, the external wake-up pin WKUP2 is enabled and triggers a wake-up from Standby or Shutdown event when a rising or a falling edge occurs. The active edge is configured via the WP2 bit in the PWR_CR4 register.

pub const fn ewup3(&self) -> bool

Enable Wake-up pin WKUP3 When this bit is set, the external wake-up pin WKUP3 is enabled and triggers a wake-up from Standby or Shutdown event when a rising or a falling edge occurs. The active edge is configured via the WP3 bit in the PWR_CR4 register.

pub fn set_ewup3(&mut self, val: bool)

Enable Wake-up pin WKUP3 When this bit is set, the external wake-up pin WKUP3 is enabled and triggers a wake-up from Standby or Shutdown event when a rising or a falling edge occurs. The active edge is configured via the WP3 bit in the PWR_CR4 register.

pub const fn ewup4(&self) -> bool

Enable Wake-up pin WKUP4 When this bit is set, the external wake-up pin WKUP4 is enabled and triggers a wake-up from Standby or Shutdown event when a rising or a falling edge occurs. The active edge is configured via the WP4 bit in the PWR_CR4 register.

pub fn set_ewup4(&mut self, val: bool)

Enable Wake-up pin WKUP4 When this bit is set, the external wake-up pin WKUP4 is enabled and triggers a wake-up from Standby or Shutdown event when a rising or a falling edge occurs. The active edge is configured via the WP4 bit in the PWR_CR4 register.

pub const fn ewup5(&self) -> bool

Enable Wake-up pin WKUP5 When this bit is set, the external wake-up pin WKUP5 is enabled and triggers a wake-up from Standby or Shutdown event when a rising or a falling edge occurs.The active edge is configured via the WP5 bit in the PWR_CR4 register.

pub fn set_ewup5(&mut self, val: bool)

Enable Wake-up pin WKUP5 When this bit is set, the external wake-up pin WKUP5 is enabled and triggers a wake-up from Standby or Shutdown event when a rising or a falling edge occurs.The active edge is configured via the WP5 bit in the PWR_CR4 register.

pub const fn ewup7(&self) -> bool

Enable Wake-up pin WKUP7. When this bit is set, the external wake-up pin WKUP7 is enabled and triggers a wake-up from Standby or Shutdown event when a rising or a falling edge occurs.The active edge is configured via the WP7 bit in the PWR_CR4 register.

pub fn set_ewup7(&mut self, val: bool)

Enable Wake-up pin WKUP7. When this bit is set, the external wake-up pin WKUP7 is enabled and triggers a wake-up from Standby or Shutdown event when a rising or a falling edge occurs.The active edge is configured via the WP7 bit in the PWR_CR4 register.

pub const fn rrs(&self) -> bool

SRAM2 retention in Standby mode

pub fn set_rrs(&mut self, val: bool)

SRAM2 retention in Standby mode

pub const fn enulp(&self) -> bool

Enable ULP sampling When this bit is set, the BORL, BORH and PVD are periodically sampled instead continuous monitoring to reduce power consumption. Fast supply drop between two sample/compare phases is not detected in this mode. This bit has impact only on STOP2, Standby and shutdown low power modes.

pub fn set_enulp(&mut self, val: bool)

Enable ULP sampling When this bit is set, the BORL, BORH and PVD are periodically sampled instead continuous monitoring to reduce power consumption. Fast supply drop between two sample/compare phases is not detected in this mode. This bit has impact only on STOP2, Standby and shutdown low power modes.

pub const fn apc(&self) -> bool

Apply pull-up and pull-down configuration When this bit is set, the I/O pull-up and pull-down configurations defined in the PWR_PUCRx and PWR_PDCRx registers are applied. When this bit is cleared, the PWR_PUCRx and PWR_PDCRx registers are not applied to the I/Os, instead the I/Os are in floating mode during Standby or configured according GPIO controller GPIOx_PUPDR register during RUN mode.

pub fn set_apc(&mut self, val: bool)

Apply pull-up and pull-down configuration When this bit is set, the I/O pull-up and pull-down configurations defined in the PWR_PUCRx and PWR_PDCRx registers are applied. When this bit is cleared, the PWR_PUCRx and PWR_PDCRx registers are not applied to the I/Os, instead the I/Os are in floating mode during Standby or configured according GPIO controller GPIOx_PUPDR register during RUN mode.

pub const fn eiwul(&self) -> bool

Enable internal wake-up line

pub fn set_eiwul(&mut self, val: bool)

Enable internal wake-up line

Trait Implementations§

§

impl Clone for Cr3

§

fn clone(&self) -> Cr3

Returns a copy of the value. Read more
1.0.0 · source§

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source. Read more
§

impl Default for Cr3

§

fn default() -> Cr3

Returns the “default value” for a type. Read more
§

impl PartialEq for Cr3

§

fn eq(&self, other: &Cr3) -> bool

Tests for self and other values to be equal, and is used by ==.
1.0.0 · source§

fn ne(&self, other: &Rhs) -> bool

Tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.
§

impl Copy for Cr3

§

impl Eq for Cr3

§

impl StructuralPartialEq for Cr3

Auto Trait Implementations§

§

impl Freeze for Cr3

§

impl RefUnwindSafe for Cr3

§

impl Send for Cr3

§

impl Sync for Cr3

§

impl Unpin for Cr3

§

impl UnwindSafe for Cr3

Blanket Implementations§

source§

impl<T> Any for T
where T: 'static + ?Sized,

source§

fn type_id(&self) -> TypeId

Gets the TypeId of self. Read more
source§

impl<T> Borrow<T> for T
where T: ?Sized,

source§

fn borrow(&self) -> &T

Immutably borrows from an owned value. Read more
source§

impl<T> BorrowMut<T> for T
where T: ?Sized,

source§

fn borrow_mut(&mut self) -> &mut T

Mutably borrows from an owned value. Read more
source§

impl<T> CloneToUninit for T
where T: Clone,

source§

unsafe fn clone_to_uninit(&self, dst: *mut T)

🔬This is a nightly-only experimental API. (clone_to_uninit)
Performs copy-assignment from self to dst. Read more
source§

impl<T> From<T> for T

source§

fn from(t: T) -> T

Returns the argument unchanged.

source§

impl<T, U> Into<U> for T
where U: From<T>,

source§

fn into(self) -> U

Calls U::from(self).

That is, this conversion is whatever the implementation of From<T> for U chooses to do.

source§

impl<T, U> TryFrom<U> for T
where U: Into<T>,

source§

type Error = Infallible

The type returned in the event of a conversion error.
source§

fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>

Performs the conversion.
source§

impl<T, U> TryInto<U> for T
where U: TryFrom<T>,

source§

type Error = <U as TryFrom<T>>::Error

The type returned in the event of a conversion error.
source§

fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>

Performs the conversion.