Struct stm32_metapac::pwr::regs::Cr1

#[repr(transparent)]
pub struct Cr1(pub u32);

control register 1

Tuple Fields

0: u32

Implementations

impl Cr1

pub const fn lpms(&self) -> Lpms

Low-power mode selection These bits select the low-power mode entered when the CPU enters the SleepDeep mode. 10x: Standby mode others reserved

pub fn set_lpms(&mut self, val: Lpms)

Low-power mode selection These bits select the low-power mode entered when the CPU enters the SleepDeep mode. 10x: Standby mode others reserved

pub const fn r2rsb1(&self) -> bool

SRAM2 retention in Standby mode This bit is used to keep the SRAM2 content in Standby retention mode.

pub fn set_r2rsb1(&mut self, val: bool)

SRAM2 retention in Standby mode This bit is used to keep the SRAM2 content in Standby retention mode.

pub const fn ulpmen(&self) -> bool

BOR0 ultra-low-power mode. This bit is used to reduce the consumption by configuring the BOR0 in discontinuous mode for Stop 1 and Standby modes. Discontinuous mode is only available when BOR levels 1 to 4 and PVD are disabled. Note: This bit must be set to reach the lowest power consumption in the low-power modes. Note: This bit must not be set together with autonomous peripherals using HSI as kernel clock. Note: When BOR level 1 to 4 or PVD is enabled continuous mode applies independent from ULPMEN.

pub fn set_ulpmen(&mut self, val: bool)

BOR0 ultra-low-power mode. This bit is used to reduce the consumption by configuring the BOR0 in discontinuous mode for Stop 1 and Standby modes. Discontinuous mode is only available when BOR levels 1 to 4 and PVD are disabled. Note: This bit must be set to reach the lowest power consumption in the low-power modes. Note: This bit must not be set together with autonomous peripherals using HSI as kernel clock. Note: When BOR level 1 to 4 or PVD is enabled continuous mode applies independent from ULPMEN.

pub const fn radiorsb(&self) -> bool

2.4 GHz RADIO SRAMs (RXTXRAM and Sequence RAM) and Sleep clock retention in Standby mode. This bit is used to keep the 2.4 GHz RADIO SRAMs content in Standby retention mode and the 2.4 GHz RADIO sleep timer counter operational.

pub fn set_radiorsb(&mut self, val: bool)

2.4 GHz RADIO SRAMs (RXTXRAM and Sequence RAM) and Sleep clock retention in Standby mode. This bit is used to keep the 2.4 GHz RADIO SRAMs content in Standby retention mode and the 2.4 GHz RADIO sleep timer counter operational.

pub const fn r1rsb1(&self) -> bool

SRAM1 retention in Standby mode This bit is used to keep the SRAM1 content in Standby retention mode.

pub fn set_r1rsb1(&mut self, val: bool)

SRAM1 retention in Standby mode This bit is used to keep the SRAM1 content in Standby retention mode.

Trait Implementations

impl Clone for Cr1

fn clone(&self) -> Cr1

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Default for Cr1

fn default() -> Cr1

Returns the “default value” for a type.

impl PartialEq for Cr1

fn eq(&self, other: &Cr1) -> bool

This method tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

This method tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl Copy for Cr1

impl Eq for Cr1

impl StructuralEq for Cr1

impl StructuralPartialEq for Cr1