Struct Hwgeneral 

#[repr(transparent)]
pub struct Hwgeneral(pub u32);

Hardware General. F70RM 44.6.1.3 (text line 112178).

Tuple Fields

0: u32

Implementations

impl Hwgeneral

pub const fn phyw(&self) -> u8

PHY Width. Read-only status/value; writes do not configure this field. Raw encoding: 00b - 8-bit wide data bus (software nonprogrammable); 01b - 16-bit wide data bus (software nonprogrammable); 10b - Reset to 8-bit wide data bus (software programmable); 11b - Reset to 16-bit wide data bus (software programmable).

pub const fn set_phyw(&mut self, val: u8)

PHY Width. Read-only status/value; writes do not configure this field. Raw encoding: 00b - 8-bit wide data bus (software nonprogrammable); 01b - 16-bit wide data bus (software nonprogrammable); 10b - Reset to 8-bit wide data bus (software programmable); 11b - Reset to 16-bit wide data bus (software programmable).

pub const fn phym(&self) -> u8

Transceiver Type. Read-only status/value; writes do not configure this field. Raw encoding: 0000b - UTMI/UMTI+; 0001b - ULPI DDR; 0010b - ULPI; 0011b - Serial only; 0100b - Software programmable: reset to UTMI/UTMI+; 0101b - Software programmable: reset to ULPI DDR; 0110b - Software programmable: reset to ULPI; 0111b - Software programmable: reset to Serial; 1000b - IC-USB; 1001b - Software programmable: reset to IC-USB; 1010b - HSIC; 1011b - Software programmable: reset to HSIC; 1100b-1111b - Reserved.

pub const fn set_phym(&mut self, val: u8)

Transceiver Type. Read-only status/value; writes do not configure this field. Raw encoding: 0000b - UTMI/UMTI+; 0001b - ULPI DDR; 0010b - ULPI; 0011b - Serial only; 0100b - Software programmable: reset to UTMI/UTMI+; 0101b - Software programmable: reset to ULPI DDR; 0110b - Software programmable: reset to ULPI; 0111b - Software programmable: reset to Serial; 1000b - IC-USB; 1001b - Software programmable: reset to IC-USB; 1010b - HSIC; 1011b - Software programmable: reset to HSIC; 1100b-1111b - Reserved.

pub const fn sm(&self) -> u8

Serial Interface Mode Capability. Read-only status/value; writes do not configure this field. Raw encoding: 00b - No serial engine; always use parallel signaling; 01b - Serial engine present; always use serial signaling for FS and LS; 10b - Software programmable; reset to use parallel signaling for FS and LS; 11b - Software programmable; reset to use serial signaling for FS and LS.

pub const fn set_sm(&mut self, val: u8)

Serial Interface Mode Capability. Read-only status/value; writes do not configure this field. Raw encoding: 00b - No serial engine; always use parallel signaling; 01b - Serial engine present; always use serial signaling for FS and LS; 10b - Software programmable; reset to use parallel signaling for FS and LS; 11b - Software programmable; reset to use serial signaling for FS and LS.

pub const fn lpm(&self) -> bool

Link Power Management Capability. Read-only status/value; writes do not configure this field. Raw encoding: 0b - Not supported; 1b - Supported.

pub const fn set_lpm(&mut self, val: bool)

Link Power Management Capability. Read-only status/value; writes do not configure this field. Raw encoding: 0b - Not supported; 1b - Supported.

Trait Implementations

impl Clone for Hwgeneral

fn clone(&self) -> Hwgeneral

Returns a duplicate of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for Hwgeneral

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Default for Hwgeneral

fn default() -> Hwgeneral

Returns the “default value” for a type.

impl PartialEq for Hwgeneral

fn eq(&self, other: &Hwgeneral) -> bool

Tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

Tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl Copy for Hwgeneral

impl Eq for Hwgeneral

impl StructuralPartialEq for Hwgeneral