embassy-stm32

Crates

git

Versions

stm32f401vc

Flavors

Struct embassy_stm32::usb::Config

·
#[non_exhaustive]
pub struct Config { pub vbus_detection: bool, pub xcvrdly: bool, }
Expand description

USB driver config.

Fields (Non-exhaustive)§

This struct is marked as non-exhaustive
Non-exhaustive structs could have additional fields added in future. Therefore, non-exhaustive structs cannot be constructed in external crates using the traditional Struct { .. } syntax; cannot be matched against without a wildcard ..; and struct update syntax will not work.
§vbus_detection: bool

Enable VBUS detection.

The USB spec requires USB devices monitor for USB cable plug/unplug and react accordingly. This is done by checking whether there is 5V on the VBUS pin or not.

If your device is bus-powered (powers itself from the USB host via VBUS), then this is optional. (If there’s no power in VBUS your device would be off anyway, so it’s fine to always assume there’s power in VBUS, i.e. the USB cable is always plugged in.)

If your device is self-powered (i.e. it gets power from a source other than the USB cable, and therefore can stay powered through USB cable plug/unplug) then you MUST set this to true.

If you set this to true, you must connect VBUS to PA9 for FS, PB13 for HS, possibly with a voltage divider. See ST application note AN4879 and the reference manual for more details.

§xcvrdly: bool

Enable transceiver delay.

Some ULPI PHYs like the Microchip USB334x series require a delay between the ULPI register write that initiates the HS Chirp and the subsequent transmit command, otherwise the HS Chirp does not get executed and the deivce enumerates in FS mode. Some USB Link IP like those in the STM32H7 series support adding this delay to work with the affected PHYs.

Trait Implementations§

source§

impl Clone for Config

source§

fn clone(&self) -> Config

Returns a copy of the value. Read more
1.0.0 · source§

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source. Read more
source§

impl Debug for Config

source§

fn fmt(&self, f: &mut Formatter<'_>) -> Result<(), Error>

Formats the value using the given formatter. Read more
source§

impl Default for Config

source§

fn default() -> Config

Returns the “default value” for a type. Read more
source§

impl PartialEq for Config

source§

fn eq(&self, other: &Config) -> bool

Tests for self and other values to be equal, and is used by ==.
1.0.0 · source§

fn ne(&self, other: &Rhs) -> bool

Tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.
source§

impl Copy for Config

source§

impl Eq for Config

source§

impl StructuralPartialEq for Config

Auto Trait Implementations§

§

impl Freeze for Config

§

impl RefUnwindSafe for Config

§

impl Send for Config

§

impl Sync for Config

§

impl Unpin for Config

§

impl UnwindSafe for Config

Blanket Implementations§

source§

impl<T> Any for T
where T: 'static + ?Sized,

source§

fn type_id(&self) -> TypeId

Gets the TypeId of self. Read more
source§

impl<T> Borrow<T> for T
where T: ?Sized,

source§

fn borrow(&self) -> &T

Immutably borrows from an owned value. Read more
source§

impl<T> BorrowMut<T> for T
where T: ?Sized,

source§

fn borrow_mut(&mut self) -> &mut T

Mutably borrows from an owned value. Read more
source§

impl<T> CloneToUninit for T
where T: Clone,

source§

unsafe fn clone_to_uninit(&self, dst: *mut T)

🔬This is a nightly-only experimental API. (clone_to_uninit)
Performs copy-assignment from self to dst. Read more
source§

impl<T> From<T> for T

source§

fn from(t: T) -> T

Returns the argument unchanged.

source§

impl<T, U> Into<U> for T
where U: From<T>,

source§

fn into(self) -> U

Calls U::from(self).

That is, this conversion is whatever the implementation of From<T> for U chooses to do.

source§

impl<T, U> TryFrom<U> for T
where U: Into<T>,

source§

type Error = Infallible

The type returned in the event of a conversion error.
source§

fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>

Performs the conversion.
source§

impl<T, U> TryInto<U> for T
where U: TryFrom<T>,

source§

type Error = <U as TryFrom<T>>::Error

The type returned in the event of a conversion error.
source§

fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>

Performs the conversion.