Struct DacChannel

pub struct DacChannel<'d, T: Instance, const N: u8, DMA = NoDma> { /* private fields */ }

Driver for a single DAC channel.

If you want to use both channels, either together or independently, create a Dac first and use it to access each channel.

Implementations

impl<'d, T: Instance, const N: u8, DMA> DacChannel<'d, T, N, DMA>

pub fn new( _peri: impl Peripheral<P = T> + 'd, dma: impl Peripheral<P = DMA> + 'd, pin: impl Peripheral<P = impl DacPin<T, N> + Pin> + 'd, ) -> Self

Create a new DacChannel instance, consuming the underlying DAC peripheral.

If you’re not using DMA, pass [dma::NoDma] for the dma argument.

The channel is enabled on creation and begin to drive the output pin. Note that some methods, such as set_trigger() and set_mode(), will disable the channel; you must re-enable it with enable().

By default, triggering is disabled, but it can be enabled using DacChannel::set_trigger().

pub fn new_internal( _peri: impl Peripheral<P = T> + 'd, dma: impl Peripheral<P = DMA> + 'd, ) -> Self

Create a new DacChannel instance where the external output pin is not used, so the DAC can only be used to generate internal signals. The GPIO pin is therefore available to be used for other functions.

The channel is set to Mode::NormalInternalUnbuffered and enabled on creation. Note that some methods, such as set_trigger() and set_mode(), will disable the channel; you must re-enable it with enable().

If you’re not using DMA, pass [dma::NoDma] for the dma argument.

By default, triggering is disabled, but it can be enabled using DacChannel::set_trigger().

pub fn set_enable(&mut self, on: bool)

Enable or disable this channel.

pub fn enable(&mut self)

Enable this channel.

pub fn disable(&mut self)

Disable this channel.

pub fn set_trigger(&mut self, source: TriggerSel)

Set the trigger source for this channel.

This method disables the channel, so you may need to re-enable afterwards.

pub fn set_triggering(&mut self, on: bool)

Enable or disable triggering for this channel.

pub fn trigger(&mut self)

Software trigger this channel.

pub fn set_mode(&mut self, mode: Mode)

Set mode of this channel.

This method disables the channel, so you may need to re-enable afterwards.

pub fn set(&mut self, value: Value)

Write a new value to this channel.

If triggering is not enabled, the new value is immediately output; otherwise, it will be output after the next trigger.

pub fn read(&self) -> u16

Read the current output value of the DAC.

impl<'d, T: Instance, DMA> DacChannel<'d, T, 1, DMA>

where DMA: DacDma1<T>,

pub async fn write(&mut self, data: ValueArray<'_>, circular: bool)

Write data to this channel via DMA.

To prevent delays or glitches when outputing a periodic waveform, the circular flag can be set. This configures a circular DMA transfer that continually outputs data. Note that for performance reasons in circular mode the transfer-complete interrupt is disabled.

impl<'d, T: Instance, DMA> DacChannel<'d, T, 2, DMA>

where DMA: DacDma2<T>,

pub async fn write(&mut self, data: ValueArray<'_>, circular: bool)

Write data to this channel via DMA.

To prevent delays or glitches when outputing a periodic waveform, the circular flag can be set. This configures a circular DMA transfer that continually outputs data. Note that for performance reasons in circular mode the transfer-complete interrupt is disabled.

Trait Implementations

impl<'d, T: Instance, const N: u8, DMA> Drop for DacChannel<'d, T, N, DMA>

fn drop(&mut self)

Executes the destructor for this type.