Struct embassy_stm32::usart::UartTx

pub struct UartTx<'d, T: BasicInstance, M: Mode> { /* private fields */ }

Tx-only UART Driver.

Can be obtained from Uart::split, or can be constructed independently, if you do not need the receiving half of the driver.

Implementations

impl<'d, T: BasicInstance> UartTx<'d, T, Async>

pub fn new( peri: impl Peripheral<P = T> + 'd, tx: impl Peripheral<P = impl TxPin<T>> + 'd, tx_dma: impl Peripheral<P = impl TxDma<T>> + 'd, config: Config ) -> Result<Self, ConfigError>

Useful if you only want Uart Tx. It saves 1 pin and consumes a little less power.

pub fn new_with_cts( peri: impl Peripheral<P = T> + 'd, tx: impl Peripheral<P = impl TxPin<T>> + 'd, cts: impl Peripheral<P = impl CtsPin<T>> + 'd, tx_dma: impl Peripheral<P = impl TxDma<T>> + 'd, config: Config ) -> Result<Self, ConfigError>

Create a new tx-only UART with a clear-to-send pin

pub async fn write(&mut self, buffer: &[u8]) -> Result<(), Error>

Initiate an asynchronous UART write

impl<'d, T: BasicInstance> UartTx<'d, T, Blocking>

pub fn new_blocking( peri: impl Peripheral<P = T> + 'd, tx: impl Peripheral<P = impl TxPin<T>> + 'd, config: Config ) -> Result<Self, ConfigError>

Create a new blocking tx-only UART with no hardware flow control.

Useful if you only want Uart Tx. It saves 1 pin and consumes a little less power.

pub fn new_blocking_with_cts( peri: impl Peripheral<P = T> + 'd, tx: impl Peripheral<P = impl TxPin<T>> + 'd, cts: impl Peripheral<P = impl CtsPin<T>> + 'd, config: Config ) -> Result<Self, ConfigError>

Create a new blocking tx-only UART with a clear-to-send pin

impl<'d, T: BasicInstance, M: Mode> UartTx<'d, T, M>

pub fn set_config(&mut self, config: &Config) -> Result<(), ConfigError>

Reconfigure the driver

pub fn blocking_write(&mut self, buffer: &[u8]) -> Result<(), Error>

Perform a blocking UART write

pub fn blocking_flush(&mut self) -> Result<(), Error>

Block until transmission complete

Trait Implementations

impl<'d, T: BasicInstance, M: Mode> Drop for UartTx<'d, T, M>

fn drop(&mut self)

Executes the destructor for this type.

impl<T, M: Mode> ErrorType for UartTx<'_, T, M>

where T: BasicInstance,

type Error = Error

Error type of all the IO operations on this type.

impl<'d, T: BasicInstance, M: Mode> ErrorType for UartTx<'d, T, M>

type Error = Error

Error type

impl<'d, T: BasicInstance, M: Mode> SetConfig for UartTx<'d, T, M>

type Config = Config

The configuration type used by this driver.

type ConfigError = ConfigError

The error type that can occur if set_config fails.

fn set_config(&mut self, config: &Self::Config) -> Result<(), Self::ConfigError>

Set the configuration of the driver.

impl<T> Write for UartTx<'_, T, Async>

where T: BasicInstance,

async fn write(&mut self, buf: &[u8]) -> Result<usize, Self::Error>

Write a buffer into this writer, returning how many bytes were written.

async fn flush(&mut self) -> Result<(), Self::Error>

Flush this output stream, ensuring that all intermediately buffered contents reach their destination.

async fn write_all(&mut self, buf: &[u8]) -> Result<(), Self::Error>

Write an entire buffer into this writer.

impl<T, M: Mode> Write for UartTx<'_, T, M>

where T: BasicInstance,

fn write(&mut self, buf: &[u8]) -> Result<usize, Self::Error>

Write a buffer into this writer, returning how many bytes were written.

fn flush(&mut self) -> Result<(), Self::Error>

Flush this output stream, blocking until all intermediately buffered contents reach their destination.

fn write_all(&mut self, buf: &[u8]) -> Result<(), Self::Error>

Write an entire buffer into this writer.

fn write_fmt( &mut self, fmt: Arguments<'_> ) -> Result<(), WriteFmtError<Self::Error>>

Write a formatted string into this writer, returning any error encountered.

impl<'d, T: BasicInstance, M: Mode> Write for UartTx<'d, T, M>

fn write(&mut self, char: u8) -> Result<(), Self::Error>

Writes a single word to the serial interface.

fn flush(&mut self) -> Result<(), Self::Error>

Ensures that none of the previously written words are still buffered.

impl<'d, T: BasicInstance, M: Mode> Write<u8> for UartTx<'d, T, M>

type Error = Error

The type of error that can occur when writing

fn bwrite_all(&mut self, buffer: &[u8]) -> Result<(), Self::Error>

Writes a slice, blocking until everything has been written

fn bflush(&mut self) -> Result<(), Self::Error>

Block until the serial interface has sent all buffered words